What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Is the a way to contol flow (Flow velocity) without impacting pressure value?

I have a pipe with 10 mm in Diameter and 2 bar pressure, the fluid velocity is 200 m/s, the fluid is air. is there a way to reduce velocity without affecting the pressure value?

25 February 2021 7,187 3 View

Can anyone suggest a topic for the Impact of AI and ML in the financial institutions?

I am currently doing my Master Thesis in FinTech and I am thinking of doing my project on the impact of AI and ML on the financial industry but as the impact of these technologies on the industry...

21 February 2021 7,128 3 View

Where I can find materials to learn Fuzzy VIKOR methodology?

Please suggest ways to learn Fuzzy VIKOR methodology in a best possible way. And is there any toolkit available for the same? Thank you in advance.

20 February 2021 8,271 3 View

What cause the beating of this signal?

I am trying to simulate the impact of a sinusoidal force on a Beam, yet I registred this beating signal (Displacement by time). The freaquency of excitation was the same as the first natural...

19 February 2021 5,872 3 View

How to apply a voltage sinusoidal/harmonic load in ANSYS APDL?

Hello all, I want to simulate a Dielectric Elastomer Actuator DAE (an electrostatic-Structural analysis). I want to apply various voltages and frequencies into the DEA in the form of sine wave....

13 February 2021 3,261 3 View

How to calculate time needed to evacuate a pressure from a tank using a pump?

Dear I have an air reservoir with 50 bar pressure , this reservoir is fed by 2 bar air pressure source, I would like to instal air pump ( 30 m3/h ) to evacuate the 2 bar fed pressure so I always...

06 February 2021 3,520 3 View

Observation instrument for classroom activity in consecutive interpreting?

Hello everybody My research involves an intervention where an instructor delivers a training course to students. My role as a researcher is to write down observations. Do you have any idea about...

03 February 2021 6,853 3 View

Inquiry regarding engineering journals for free publications for my dissertation (laser polishing of 3D printed parts?

my dissertation was on laser polishing of 3D printed plastic parts, i want to publish it, can anyone suggest me a free copy engineer journal for this purpos, plz?

01 February 2021 7,140 4 View

Is diversity in teaching methods for students important in communicating information?

Is diversity in teaching methods for students important in communicating information?

26 January 2021 3,387 7 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

What could be the reason for not having further low chi square value (better agreement) in my refinement result?

I have tried every combination of parameter changes and after that i have a poor chi square value. I can't get it lower any further. I know there have been a lot of discussion about Rietveld...

26 February 2021 8,480 3 View

Which software is best to analyse multi-phase fluid flows ?

Hello everyone, hope all is good. I want to analyse multi-phase fluid flow through pipe, which software is best to do so ?

21 February 2021 4,230 8 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

How to compare different models with different inputs and data length?

I want to run 5 different models to estimate stream flow. In order to optimize the characteristics of these models I use Taguchi method. So I have to run different models according to the Taguchi...

11 February 2021 7,986 6 View

Does Abaqus plugin AM-Modeler predict the same temperature/crystallinity history as UMATHT user-subroutine?

During AM process, progressively activation of elements can predict the temperature/crystallinity history, including surroundings heat losses and than this data could be used to determine the...

06 February 2021 4,686 1 View

No title

29 January 2021 2,623 1 View

What stress-strain graphs do I put in a smeared concrete and steel reinforcement element in finite element analysis?

My SOLID65 element is reinforced concrete but what modulus of elasticity and material properties do I put? For nonlinear analysis

26 January 2021 1,704 3 View