Kindly if any specialized in this field could help me 🙏🏻 thanks
I will try to give
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...
04 August 2024 3,461 3 View
Material : Fiberglass sheet thickness : 3mm
03 June 2024 6,255 0 View
The best definition of heterostructure.
16 May 2024 9,848 1 View
Is there any mathematical relationship between zeta potential and both the polydispersive index (PDI) and pH of the zero-point charge of the nanoparticles?
28 April 2024 8,728 5 View
Hello, I recently updated my MacBook to Sonoma and after installing the newest Java version which was necessary to get Mplus to run, everything looked fine. But now when I want to run an input...
09 April 2024 7,783 1 View
what is the procedure of synthesis of nanomaterial -Bottom-up -Chemical Etching? Advantage and disadvantagesAdvantages of this technique?
04 April 2024 2,522 2 View
how can we create these plots? a 3-dimensional look and showing strength with colour, which software does create these pictures? source of image: Directive giant upconversion by supercritical...
02 April 2024 9,999 4 View
Hi everyone, I was recently doing a simulation and actual measurement of a rectifier circuit, using the series diode SMS7630-079LF (Breakdown Voltage=2V). The output DC voltage obtained by my...
21 March 2024 1,166 2 View
Is it possible to grow graphene on the vertical wall of a structure, for example on the vertical walls of a SOI waveguide?
09 March 2024 1,990 2 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...
07 August 2024 1,686 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...
07 August 2024 3,218 4 View
Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...
06 August 2024 666 4 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
