13 June 2017 4 5K Report

I am looking for an paper with investigation of coherence times for urban and suburban areas NOS fixed wireless TX and RX / dynamic channel ?

More Geetanjali Choudari's questions See All
How to plot the dispersion band diagram for metal based photonic crystal using COMSOL?

I am learning the COMSOL software to study the band diagram of different photonic crystal structures. For a dielectric-based photonic crystal, only the k parameter sweep is needed to study the...

25 March 2024 3,514 1 View

Graphical neural network?

Need study material on Gnn

11 September 2023 5,441 1 View

Retrograde tracing with FluoroGold without transcardial perfusion?

Has anyone had success with retrograde tracing of peripheral axons using FluoroGold but without perfusing the animal with paraformaldeheyde at the end of the timepoint?

11 September 2022 3,423 0 View

Can DNA be stored in the same deep freezer where plasma or serum aliquots are being stored?

Can DNA (extracted from feces) be stored in the same deep freezer where plasma or serum aliquots are being stored? Can DNA (extracted from pleural fluid) be stored in the same deep freezer where...

09 October 2021 6,948 3 View

What should be the approach to write a survey paper for a field where much work hasn't been done yet?

There are other correlated problems and fields but I want to write a survey paper for the problem not explored much.

07 June 2021 5,752 3 View

Sir Can you share the code for creating custom dataset for landcover mapping from satellite images?

I am working on using deep learning for geospatial data analysis.

14 May 2021 2,922 6 View

I m currently trying to do some research on biodeterioration of stone, suggest some good topics to study?

i m searching for dissertation topic

02 March 2020 7,658 3 View

What is the procedure of placing lime treated samples in a humidity chamber?

Dear Researchers, I am curing my lime treated samples in humidity chamber. But I am not sure weather I need to wrap the samples with plastic and place in chamber or I need to keep the samples...

23 October 2019 8,232 2 View

Dear Researcher, Are there any papers related to experimental pushover tests on ductile reinforced frames?

It am looking preferably for the one performed recently.

13 December 2018 8,760 0 View

Can someone provide me some help, with a 3D heatmap?

I for a way in creating a 3d smooth plot like a heat map with peaks in matlab. As x coordinate I have the longitude (gps coordinate) as y coordinate I have the latitude (gps coordinate) and as Z...

01 January 2018 6,777 4 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close