I am interested in using Biotek CYTATION 3, is it possible to use microplates with glass bottoms?

16 June 2025 1 499 Report

It is mentioned in the manual of Biotek CYTATION 3, to use different well plate with standard geometry but not specifically if to use glass bottom based well plates. Is it possible?

Emmanuel Ansong Adjei

Yes, you can definitely use glass-bottom microplates with the BioTek Cytation 3. This instrument supports imaging with clear/optical bottoms, including both glass and thin-film bottoms recommended for high-resolution fluorescence microscopy.

Badges
Science topic

More Bazila B.'s questions See All

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

Can any of you suggest how to find the detection limit.?

I am working on flourescence sensing of heavy metals using quantum dots.Can any of you suggest how to find the detection limit. Whether it is calculated from formula or we can get from instrument?

19 July 2024 7,411 3 View

Cloning of flaviviruses is difficult i have noticed that cells loose their transformation ability after cloning fragments inside vector any advice?

As flaviviruses genome is very frequently prone to mutation hence it is very difficult to clone whole genome inside vector what kind of vector and cells can sustain such amount of cloning...

11 July 2024 4,284 0 View

I am not getting proper colonies while ligating one of fragments in my vector the colonies seems to be normal but in light it seems lysed any reason?

I am working on cloning of a gene fragment inside my vector everything we tried to do correctly like making insert and vector with utmost care but after ligation the morphology of colonies seems...

11 July 2024 9,010 3 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

I have a doubt in finding the amount of ferromagnetic and antiferromagnetic contribution in a canted system?

Is it possible to differentiate or calculate, the amount of ferromagnetic and antiferromagnetic contribution in a canted system? (Weakly frustrated canted antiferromagnetic system)

25 June 2024 6,210 0 View

How transmittance is dependent on the band gap and atomic structure?

UV-Visible NIR analysis

20 June 2024 9,056 3 View

Whether size obtained from TEM and XRD should be equal?

I have got crystalline size around 15nm from xrd but TEM is giving particle size 4nm

20 June 2024 6,064 8 View

If I dop a metal ion into the ternary nanoparticles can I call it as heterostructure?

Ag+ ion replaced some of the Cu+ ion. ie, Ag+ is the dopant

14 June 2024 2,814 1 View

Whether the same synthesised inorganic nanoparticle show different heavy metal sensing by flourescence?

14 June 2024 7,373 1 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View

Publishing a checklist?

Does anybody know of entomological Journals without page charges that would publish an extensive checklist (Hong Kong Aculeates wasps) covering 350 species (of which more than half are new to Hong...

01 August 2024 6,134 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

How can I use DFT-D3 correction ( Siesta version 5.0.1)?

Dear Siesta Users, I installed Siesta 5.0.1 and I want to use Grimme's D3 correction. According to the 5.0.1 manual, I could use a few parameters to include the D3 correction in the...

27 July 2024 5,748 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View