Hydropower Designing and Modeling as a final year project in Civil Engineering

More Subash Gupta's questions See All

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Some new emerging problems on application of RL for scheduling in IoT networks?

I have seen plenty of existing works on applied Reinforcement Learning (RL) policies for optimized scheduling in IoT networks including Q-learning, DQNs, and the newer ones including PPO for...

01 August 2024 8,754 2 View

How to make soil water characteristic curve using centrifuge?

We have no access of pressure plate apparatus

22 July 2024 3,488 2 View

What is the degassing temperature and time for biochar for BET surface area analysis if TGA is not possible?

Since BET and TGA both are very costly instruments and many places the facilities are not available (for large number of samples) hence a threshold degassing temperature and time is preferable

16 July 2024 8,112 2 View

Can we analyse RMSD for peptide-HLA docking and binding affinity for peptide-HLA to TCR docking, in a peptide-HLA-TCR docking ?

In the peptide-HLA-TCR docking process, can we express the result of peptide-HLA docking in RMSD and for peptide-HLA to TCR docking, can results be expressed in binding affinity?

11 July 2024 4,831 0 View

How to get discharge capacity of a bole well?

No data regarding radius of influence is provided and no pumping test data available.

10 July 2024 7,168 0 View

How to apply an external electric field in gaussian 16 or Material studio DMOL3 ?

I need to apply an external electric field to 4-hydroxybenzoic acid to compare the molecule's reactivity descriptors. Could you guide me on how to apply the electric field using Gaussian and...

01 July 2024 4,192 3 View

How can I precipitate a protein from condition media ?

So I want to see is the level of a secreted protein in the condition media via western blotting What my doubt is 1. How much cells should I seed and what should be the volume of condition...

19 June 2024 1,927 1 View

Ni-NTA protein purification - how to obtain higher yield concentration?

Hello, I am trying to purify a 6X-His tagged protein using Ni-NTA chromatography. However, I obtain very less yield & concentration; and considerable protein in load flow through. Any...

16 June 2024 5,876 5 View

In sds page and western blot, non specific expressed protein with very thin band is also there along with thick band of specific protein. why ?

Asper discussion, First time my clonning was failed becuase the first 45 nucleotide was not cloned in pet30 a vector then I choosed the different clone of 1:1 ration fraction, I got the size of...

13 June 2024 7,564 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

Shishir Bhusal

First understand the components of a Hydropower plant and research in detail about the guidelines based on the components and the desired output. You can prepare a report based on how to design each and every components of the hydropower plant.

Subash Gupta

Shishir Bhusal Thank you sir.

We are following guidelines provided by DOEd. Can I contact you, if you can guide a bit.

Dileep Kumar Chandragiri

Hi Bhusal,

I'm working as a structural design consultant for Hydro power projects from last 14 years, if u need any guidance can ping me.

Thanks & Regards

9650376635