How we coat polypyrrole material on graphite sheet

More Rinki Malik's questions See All

Electro polymerization in graphite sheet?

How to do electro polymerization on graphite sheet of pyrrole in aqueous solution. Mention electrolyte use, method, charge and potential. Which method is appropriate CV, chrono potentiometer,...

04 May 2018 4,145 3 View

CV is right or not for supercapacitor?

I am new in this work. I take CV first time. I do not graph is right or not because break is found in CV. Why this is happen. Tell me soon . Thank you in advance for your answer. What is the...

08 September 2017 613 1 View

What should be potential window?

For 2M KOH as electrolyte what should be the potential window in super capacitor with polypyrrole

06 July 2017 7,356 0 View

Charge discharge procedure in nova software

Hello I am new for nova software.How to do charge discharge in nova, where we have put value of potential and current for super capacitor application. Please send full procedure. email id : ...

06 July 2017 502 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Binder for ZnO nanoparticles in graphite paste electrode?

I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?

03 August 2024 4,624 3 View

Why chloride turns into chlorine gas in a Downs cell?

I imagine the battery drives the graphite into a carbocation, then chloride is oxidized to donate the electron to the carbocation, but what pushes the lost electrons of chloride to be shared...

03 August 2024 5,384 0 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,070 3 View

Short Synthesis of Graphene Oxide from Natural Graphite Flakes?

I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...

01 August 2024 8,368 2 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

How can I separate graphene from amorphous carbon of similar particle sizes?

The starting material is a finely ground powder. Some particles contain more graphene than others.

30 July 2024 3,978 2 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

Mohamed Gobara

Hi Malik

Since graphite is conductive, you can easily electrodeposit PPy on the surface.

One key to this process is the distillation of Py before using.

But I do not understand what do you mean by " material come in to electrolyte solution.So I can not take graph."

could you please give more details.

Gobara

Rinki Malik

Hello sir

I made material by chemical oxidation method.Then we coat it on graphite sheet . Coating not stay on graphite sheet it come in to electrolyte solution

Which binder I have to use