Which SAR dataset to use for generating coherency matrix and performing target decomposition (Description) ?

Working on chandrayaan-2 DFSAR data, there are three datasets available: 1) Slant range image data product: The slant range complex image file. Each pixel is represented by two 4-byte floating...

02 March 2021 8,481 3 View

How to design a boost converter for a mppt controller?

I have a doubt on how to select the inductor and capacitor value when I want to implement MPPT controller. This is because we always take a maximum output voltage and current but in this case, we...

28 February 2021 3,637 2 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

How to calculate refractive index (n and kvalue) against energy (in eV) data for alloyed nanomaterials through Independent Phase Approximation method?

Suggest me the method or some other software to calculate the above said data for nanoparticles.

21 February 2021 3,350 7 View

How to find the air side pressure drop in a spiral fin tube bundle cross flow heat exchanger?

How to find the air side pressure drop in a spiral fin cross flow heat exchanger? The pressure difference at the inlet and outlet is very low compared to the experimental results, which I...

18 February 2021 1,109 2 View

Any methods to train a neural network with random (stochastic) and non-measurable variable?

Dear scholars, I was wondering if there are any scientific methods to train a neural network or ANFIS when one of the input variables is stochastic (random) and more importantly non-measurable?...

17 February 2021 1,909 3 View

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View

What is best technique to quantify necrotic cell death of specific cell populations?

I currently using FACS (Aurora Cytek) to quantify necrotic Gr1+ cell death from the spleens of immune competent mice. I target Gr1+ cells in the spleens of tumor-bearing mice using a photodynamic...

08 February 2021 733 6 View

Has anybody administered MK-2206 (an orally active, allosteric inhibitor of AKT) intravenously to the mice?

We aim to use MK-2206 to inhibit AKT in mice. However, a large body of studies suggests that it should be administered orally. I was wondering if somebody could tell me that is it toxic for the...

07 February 2021 6,340 1 View

Can I modify vermiculite or perlite by adding nutrients to control a certain situation?

I need to assimilate a determining condition for the plant. However, I need to ask you if it is possible to change the properties and concentration of plant nutrients in this material like perlite...

04 February 2021 8,616 11 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

Anybody with an idea on how do design specific primers for detecting tomato resistance genes tm-1, TM-2 and Tm2^2?

I am trying to identify these 3 genes among some tomato cultivar collections and after aligning some sequences from NCBI, I couldn't find unique sequences to target for specific primers. There...

28 February 2021 606 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View