Hello All
i want to design a reconfigurable antenna for which i have to use PIN diode as a switch.
anyone help me how to add PIN diode in CST i mean in schematic ??
Thank you
You may use the equivalent circuit mentioned in the datasheet for the ON and OFF case to represent the PIN diode.
To do liquid biopsy and look for specific gene expressions there are so many published papers. Thera are different protocols and procedures used to isolate circulating cell free RNA or mRNA from...
23 February 2021 7,326 5 View
Hello, I have been trying to isolate RNA from EVs (from MSCs) for a while. I isolate the EVs using SEC. Then I use the "Total Exosome RNA and Protein Isolation Kit" from Invitrogen. When I...
21 October 2020 8,559 4 View
I am trying to append .h5 files saved in a directory for my training set using Python, but I face memory error as the Data set is very large. The following code is what I used for...
23 April 2020 9,649 2 View
I some papers, the mean square error is considered. In some other, the mse is normalized by dividing the error by the (total sampling instants x the total length of the reference...
25 February 2020 784 4 View
what is the most reliable guide for identification of alternaria species based on morphological and cultural criteria?
02 December 2019 174 1 View
In "Simultaneous Stabilization and Tracking of Nonholonomic Mobile Robots: A Lyapunov-Based Approach", the authors stated that the nonholonomy of mobile robots allows control of the system with...
27 May 2019 7,721 4 View
18 May 2019 631 6 View
Dear all, Which tool is more reliable? CHOP CHOP or CRISPRdirect? I need some information about other tools and softwares. Thanks a lot
08 May 2019 10,004 2 View
Higher Education cost is increasing and students encounter some challenges to afford it.
21 March 2019 7,173 6 View
I have a thin film of a fluorescent material and want to make a reference sample with similar reflection in both visible and infrared to do the comparison. How can I make the reference sample?
26 February 2019 6,857 3 View
im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...
02 March 2021 2,246 2 View
I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...
01 March 2021 9,701 5 View
Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...
28 February 2021 7,016 1 View
I have designed a 24 GHz rectangular antenna on HFSS 3D model and got desired results while desing the same antenna with same dimensions I am getting resonance frequency at 27 GHz I am...
28 February 2021 4,426 2 View
28 February 2021 5,433 3 View
Hello everybody! I have a problem with developing a compact antenna for the 1MHz-5MHz frequency range. Tell me what type of antenna can be used and what books and articles to read to perform this...
27 February 2021 7,710 4 View
I am simulating helix antenna in hfss, right now, giving excitation with 50 ohms port. When I see the results of Z parameter (real). It shows lower than 50 ohms. Do not understand, if it can be...
27 February 2021 4,218 7 View
I recently switched the company where we buy our DMEM/F12 and i have noticed a signficant change in growth for my human olfactory neurosphere cell lines
24 February 2021 2,268 3 View
Hi everyone, I am currently running a mixed-mode simulation of a DCB using a user-defined cohesive zone model (UEL), however, the results I am getting don't make sense. I used the same UEL for...
24 February 2021 4,157 1 View
Greetings to all of You! I have searched some research papers for the designing of a proximity coupled patch antenna. Researchers are talking about the impedance bandwidth of the antenna but...
24 February 2021 7,662 3 View