No title

Hi there! I'm very new to r and trying to run a multi-level meta analysis using pre-calculated effect sizes. I've attached the datafile below. The script I used as a first step to fit the model...

12 January 2021 8,214 2 View

How to purify a recombinant protein from Ecoli to reach a cell culture purpose?

05 October 2020 502 7 View

Can hypoxic air (1% O2, 5% CO2, 94% N2) buyed from the market?

I need hypoxic air (1% O2, 5% CO2, 94% N2) for hypoxia experiments, can I get/buy some hypoxic air from the market?

14 July 2020 5,471 2 View

How to improve the thorn resistance of textiles?

Unlike body armor, the body armor faces a smaller area of knife tip. Although the energy is small, some body armor does not prevent the knife from penetrating.Moreover, if the use of composite...

24 November 2019 928 4 View

Theoretical max-min of Gibbs free energy?

Hello all, Does anyone know if there is a theoretical maximum and minimum for the Gibbs free energy? In other words, under constant physiological conditions, can one calculate the possible...

04 July 2019 8,773 5 View

Optical and radiative properties of molten salt?

The thermal radiation transfer in molten salt is usually neglected in researches. Does anyone knows the reason ? Are there any research (experimental data) focusing on the absorption coefficient...

30 June 2019 1,243 3 View

What about Multiple comparisons in a linear mixed model in R?

I'm doing the analysis with a linear mixed model.Because the sample size is different, the Scheffe test is used for the multiple comparison of my data. However, I do not know how to write code in...

09 January 2019 2,517 6 View

Apply concentrated pore fluid: This node set is not active in the model?

Hi everyone, I was modelling DFIT (Mini-fracturing) in Abaqus and applied a concentrated pore fluid into my model. However, there is error saying: A concentrated load has been specified on node...

04 December 2018 7,840 2 View

How to simulate the wick structure in a loop heat pipe?

Dear researchers: I am a newbee in the CFD simulation. Now I wish to simulate the wick structure by Fluent and the evaporation process in this region. The wick is saturated with water and being...

18 September 2018 9,281 12 View

Research problem in Agriculture using predictive analytics ?

How predictive analytics can be used in agriculture?

22 June 2018 4,484 4 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View