How to simulate zing leaching in mixing vessel(continuous stirred tank reactor) on cfx?

Manuchehr Javadivand @Manuchehr-Javadivand

22 December 2019 0 9K Report

Hello CFD expertise!

MRF method is used to the simulation of steady single-phase flow in mixing vessel. how could simulate slurry of zing ore dissolved in acid sulfuric with lime(alkaline) and water on cfx?

Badges
Science topic

More Manuchehr Javadivand's questions See All

In fluent, which BC must specify after creating a periodic boundary condition for side1 and side2 in no-pressure drop periodic flow?

I want to simulate in fluent a structure with 6 rows of steel that 22-degree water inter and pass through it then exit with 25-degree. There is a hot external airflow around this structure....

24 April 2020 2,077 3 View

In cfx, which interface model the particles can pass through? frozen rotor or stage?

transient sliding mesh method used for the simulation of two-phase liquid-solid in stirred tank reactor. in cfx manual mentioned that first use the frozen rotor for better convergence behavior...

08 January 2020 8,201 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to confirm the site-directed mutagenesis result without performing NGS?

I'm cloning a fragment of 3200 nts into plasmid. The cloning was successful, however, 02 amino acids were mutated. Now I want to fix these 02 aa by site-directed mutagenesis technique using...

08 August 2024 4,645 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Why is electronic energy 0.000 for liquid crystal compounds and is invariable with temperature in Guassian 09 software?

Are there any suggestions or insights you can provide to help address this problem

06 August 2024 1,443 2 View