How to set flow rate of a chemostat to simulate human peristalsis?

25 February 2020 0 9K Report

Hello,

If I wanted to simulate the flow rate present in the human intestine, what rate should I set in a chemostat?

A standard value I have is 0.05 h^-1 (I assume mL/h) but would that be correct? The papers I have found show a loto of computations but no number...

Thank you

Badges
Science method

Similar topics
Biological Science
Ecology

More Luigi Marongiu's questions See All

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

How to stain bacterial surface for electron microscopy?

I would like to investigate the surface of bacteria using electron microscopy to assess changes in specific conditions. Is there an established protocol for that? Thank you.

15 July 2024 2,338 2 View

How to assess bacterial permeability?

Is there an established protocol to measure the permeability of bacterial membranes? Thank you

30 June 2024 6,614 3 View

How to immobilize bacteria without morphology alterations?

I have a set of bacteria that I stained with fluorescent dyes to check for viability. The protocol suggests to place 5 ul of the suspension on a slide, cover with a cover glass, and observe on a...

16 June 2024 9,382 1 View

How to transfect environment bacteria?

I would like to transfect bacteria with some plasmids. However, the bacteria are not competent but either isolated from the environment or purchased reference strains. Can I transfect these...

16 June 2024 9,384 6 View

How to describe statistical values in words?

After performing statistical analysis, there is the need to report the p-values in the text. Is there an accepted (published) stratification range? For instance, is 0.04 'slightly' significant?...

28 May 2024 7,724 3 View

How to assess if Kd values (constant of dissociation) are meaningful?

I used Microscale thermophoresis(MST, from Nanotemper) to determine the constant of dissociation (Kd) between a protein (20 nM) and a ligand (1:2 serial dilution from 50 μM to 1.5 nM). I ran the...

04 May 2024 2,066 0 View

How to stain live bacteria for real time tracking?

I would like to track in real time the growth of bacteria using fluorescent miscoscopy. I remember there was at least one plasmid that could be used: transfected bacteria would emit a red or green...

29 April 2024 7,095 3 View

What magnification for organoid imaging?

Hello, I would like to take some publication-quality pictures of organoids. What magnification shall I use? Do I need a 60x or is a 40x enough? Thank you

15 April 2024 8,471 1 View

How to sterilize pipette without autoclave?

Hello, I think I am using a 5 mL pipette that is contaminated with bacteria. Nothing serious, just the usual environmental microbes. The problem is that the tips for the 5 mL pipette are without...

07 April 2024 6,716 1 View

How do you delete a duplicate pdf for the same paper on ResearchGate?

The first pdf file I uploaded had an error. So I uploaded an updated, corrected pdf of that paper with a different pdf name. I dpon't want the old copy to be download or read.

07 August 2024 9,508 1 View

What is the ionic radius of Hydrogen anion? And how to know the exact ionic radii of the elements?

I'm trying to calculate the tolerance factors of the hydride perovskite and the value calculated by me and the reported values are contradictory. Need more clarity in using the correct ionic radii...

01 August 2024 2,614 1 View

When I simulate for S parameters using ADS, I have faced this issue that I have attached. Please anyone clarify me?

...

31 July 2024 1,671 3 View

How to change the version of the article full-text pdf file?

How to change the displayed full article text to its corrected version? In the file on the page of the journal where I published the article, there was an error in the text, the table is...

30 July 2024 3,229 2 View

Entropy measure and QSPR modeling in Graph Theor. How to construct the table for lengthy equation?

The entropy measured of molecular graphs plays a crucial rule. The network structures in some cases are very lengthy calculations to handle. Some author avoid to construct table where as most...

30 July 2024 3,126 0 View

How do I correct that wrong author's profile in my publication?

I am writing to request a correction regarding the affiliation of one of my co-authors, Donald Ho. Currently, the author's profile incorrectly lists an affiliation with The Hong Kong Polytechnic...

28 July 2024 6,824 0 View

Wrong out put for gmx x2top?

Dear users, I would like to simulate a zeolite structure in gromacs. I got the .cif file from IZA expanded in one direction in Materials Studio and exported a .pdb file. However, when I want to...

24 July 2024 367 4 View

How to estimate a protien's size using Chimera or PyMol? how correct this estimated can be?

I need to know the approximate size of my target protein for Negative-stain EM. I have an alpha-fold predicted structure of the protein. I do not see any turtorial on internet for estimating the...

21 July 2024 5,732 3 View

Why is this tissue slice different?

This is a slice of intestinal tissue from the Chinese mitten crab (intestine in the upper right corner). I injected WSSV into this horseshoe crab. Now I want to know what these red spots next to...

18 July 2024 5,602 0 View

How to ask to correct the Incorrect Claim regarding the writer of Article that I was involved in?

Dear sir/Madam, I am Parinaz Parsa the first writer of article "Optimisation of probiotic yoghurt production enriched with phytosterols" and understand that one person is mentioned as writer which...

14 July 2024 9,579 2 View