How to remove stickiness of Sylgard?

More Kurbanova Aliya's questions See All

Has someone used ReliZyme for enzyme immobilization?

We would like to immobilize phytase (Molecular weight is around 80 kDa) on ReliZyme carrier. Would someone be so kind to help us in selecting the best option, since they have variety of them?

20 May 2018 4,284 6 View

Indigenous Ethical Guidelines and Training Manual for Online Counseling in Pakistan

I am working on a project - Therapism - that aims at providing online mental health services by connecting Counselors and Clients. (More information at: https://www.therapism.com/) Presently, I...

01 January 1970 3,457 3 View

Everyone stay at home OR Everyone come out?? :Would the virus run out of mutations work if we use lab animals?

The virus has an algorithmic behavior. And we still don't have enough info on how its mutating and adapting. Its either "stay at home" and deprive the virus from a host. Or "everyone come out and...

01 January 1970 9,906 7 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

What is the best solvent to remove PDMS from nano particles?

I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...

24 February 2021 7,845 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How can I measure the surface interaction or surface interfacial chemistry between polishing abrasives and upper surface of substrate ?

I am working on polishing abrasives. I need to do few characterizations ? which can provide the on time surface chemistry of substrate with polishing abrasive during optical polishing. I would...

18 February 2021 5,319 3 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

Jasper Giesler

Hey

Maybe check these procedures:

https://doi.org/10.1371/journal.pone.0004572

Gajasinghe, R.W.R.L., Senveli, S.U., Rawal, S., Williams, A., Zheng, A., Datar, R.H., Cote, R.J. and Tigli, O., 2014. Experimental study of PDMS bonding to various substrates for monolithic microfluidic applications. Journal of Micromechanics and Microengineering, 24(7), p.075010.

Hope this helps!

Jasper

Kurbanova Aliya

@Jasper Giesler. Thanksin advances

Alan F Rawle

You do not state what siloxane concentration you are using - perhaps it's way too high? I think you need to have about 0.1 - 1% siloxane in the hexane applied ideally by spin coating. See attached.