How to remove bubbles from buffer B for MARS 14 column using for immunodepletion?

29 October 2021 1 7K Report

While performing Immunodepletion using Agilent MARS 14 column, I had experienced many bubbles in Buffer B even after purging it for more than 15 minutes. The bubbles were forming continuously inside the buffer bottle. Is there any way to get rid of it?

Bahjat Alyas

Interesting

Badges
Science method

More Hemant Kumar's questions See All

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

What is the relationship between the threshold voltage and the device's noise performance, particularly in terms of flicker noise and thermal noise?

The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...

29 July 2024 3,246 0 View

What is the solvent system required to run tlc for calixarenes?

If you don't understand my question let me know

21 July 2024 563 1 View

Sample size for qualitative study?

I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...

20 July 2024 9,153 11 View

How to convert available phosphorus to total phosphorus?

I need to convert Available phosphorus into total phosphorus

18 July 2024 6,799 3 View

Can it is possible to find the cleaved sequence when a protein cleaved by a heamaglutanin protease (HA/P) by any bioinformatics tools?

Bioinformatics tools like peptide cutter

15 July 2024 6,453 1 View

How to calculate percentage cumulative drug release?

How to calculate percentage cumulative drug release when, Total volume of dissolution media = 250ml Added formulation was equivalent to 10mg of drug Sample withdrawn = 1ml each time Sink condition...

15 July 2024 4,192 1 View

Can we progress towards defining obesity based on body fat content?

The burden of obesity is enormous. The greater challenge lies in accurately diagnosing obesity at the right time, reflecting the true increase in visceral fat. BMI may not accurately represent...

14 July 2024 8,771 4 View

How does high humidity affect the growth and development of crops?

10 July 2024 7,258 20 View

In what ways does high humidity impact the pollination process in agricultural plants?

10 July 2024 7,513 13 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

RNA Extraction Using Hot Borate Method No Longer Working?

I've been performing RNA extraction on cotton petiole tissue for a few months now using the method described in the following paper, a derivative of the typical hot borate method...

08 August 2024 9,882 2 View

Can I use a HisTRAP column for affinity chromatography?

I'm working on selecting antibodies against a recombinant protein that has a His-tag. My idea is to first bind the recombinant protein to a HisTRAP column and then use this column for an affinity...

07 August 2024 505 3 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Hi, please what is the best tool on Aspen plus that can help me get the best inlet temperature and pressure for cryogenic distillation?

I am trying to recover liquid CO2 from a mixture of 0.6 CO2, 0.3 N2, and 0.1 O2. My aim is to recover about 99% liquid CO2 at the bottom of the column and make sure the amount of gaseous CO2...

06 August 2024 4,611 0 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View