What is the institute/organization that provides training for hydroponics development ?

I also want to know the organization working on development of nutrient solution for hydroponics and the organization providing training on it.

02 June 2020 8,901 4 View

Is there a way to correlate one-dimensional netcdf data (like a time-series data) with the spatial gridded dataset (which is multi-dimensional)?

For eg. I have a netcdf file which is in the form of a time-series and the other data is a gridded .nc file for geopotential height. I want to correlate both of these datasets. Please guide me...

27 May 2020 8,133 3 View

T-cell from frozen spleen?

Hello, I have some frozen spleen from young and old mice and wanted to isolate T-cells from these spleens. These spleens were snap-frozen and stored in -80. They were never thawed. So, I was...

12 May 2020 4,810 3 View

What kind of properties are needed in ANSYS or other FEA packages to conduct the stress/strain analysis of 2D materials under tension, and bending?

I want to simulate the effect of stresses on a graphene monolayer and observe the deformations appearing in the material. The problem is the understanding of the element size and how to define a...

02 August 2019 9,005 4 View

IP with HSF1 antibody in liver tissue??

Hi, I am trying to perform IP with HSF1 antibody from liver tissue but no success so far. I prepared my tissue lysate in RIPA buffer and I am using 1mg protein for IP and bead used is protein A/G...

04 February 2019 9,691 7 View

I am working on Brain tumor segmentation/detection using ANN,watershed and morphological operations but i lack images with grand truth any help?

I need small Training and test data with valid grand truth for my MS.c project regardless synthetic or real, if anyone can point me in right direction i would really appreciate it. "BRATS" isn't...

24 August 2016 2,757 4 View

What's the best method/alternative to wirebond to flexible mica substrates?

I have bondpands patterned on flexible mica substrates (cleaved thin disks of muscovite mica, ~100um thick). The pads are usually e-beam evaporated Ti/Au or Ti/Pd metal stacks of thickness 5/100...

06 July 2016 9,883 3 View

Trying to detect fluorescent labeled S. aureus in media containing lysed erythrocytes and plasma. What parameters should one use?

S. aureus cells are labeled with mCherry or GFP, cannot use side scatter analysis because of lysed erythrocytes. Need to detect specific cell counts based on flourescence events for number of cell...

11 May 2016 3,322 3 View

How to prevent cell clumping in matrigel invasion assay?

I am working with a cell line that migrates very well in transwell migration assays, but when I try to do an invasion assay, the cells clump together within 2-3 hours after plating. I plate them...

05 May 2016 6,261 2 View

Which part of the body/tissue is best for DNA isolation in relation to DNA Barcoding of marine molluscs?

05 September 2015 7,739 3 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View