How to reduce the tip pressure or fuel pressure for Fired heater optimization?

15 August 2023 1 4K Report

natural draft furnace (fired heater) is designed for 620°C outlet temperature of process gas , due to high fuel pressure (tip pressure) we are not able to increase the heat load .

how can we reduce the tip pressure in running plant.

Peter Van Kampen

Increase the area of the outlet orifices of the fuel gas at the tip of the burner.

Badges
Science topic

Similar topics
Geoscience
Asia
India

More Ankit Dwivedi's questions See All

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,991 0 View

What is meant by baseline of FTIR data?

I got comment on my FTIR data figure from a reviewer. The reviewer said "FTIR data in Figure should be repeated. there is no bassline." I made Y off set comparison graph of FTIR on OriginLab. Can...

03 August 2024 6,069 3 View

To perform transfection with DharmaFECT Duo in AGS cells. Could you tell me what the ideal concentration is to avoid significant cytotoxicity?

I would like to perform transfection with the reagent DharmaFECT Duo (Horizon) on the AGS cell line. Could you please inform me of the optimal concentration to use without causing cytotoxicity in...

03 August 2024 3,850 1 View

What is Random Audit?

HI there, I've came across several articles discuss about random audit an Non random to tax evasion or compliance. Most of the articles is relating about effect of audit (random or non random)...

31 July 2024 5,308 7 View

Is the mentioned CV graph a valid one as this graph have only one peak prominent (reduction)?

I have used Prussian blue nanoparticles as a redox couple. The PBNPs have been made using only one salt precursor. Also, during scan rate studies, a small oxidation peak can be consistently found...

31 July 2024 9,697 0 View

How we can use lattice-based cryptography for construction of S boxes?

Please suggest basic literature on lattice-based cryptography. A kind response from the cryptographic community will be highly appreciated.

24 July 2024 6,290 4 View

I am working on III-V based tandem solar cells.Can anyone explain that solar cells work under forward or reverse biased conditions?

I want to know that n-doped side of solar cell is connected with positive or negative electrode.

20 July 2024 1,346 2 View

Can it is possible to find the cleaved sequence when a protein cleaved by a heamaglutanin protease (HA/P) by any bioinformatics tools?

Bioinformatics tools like peptide cutter

15 July 2024 6,453 1 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,489 0 View

FACS markers to characterize rat bone marrow-derived macrophages?

Dear all, I am looking for FACS markers to characterize my rat bone marrow-derived macrophages (M0). They were differentiated from monocytes with M-CSF. I am considering to use CD11b/c and...

15 July 2024 4,615 1 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,402 2 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,524 4 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,952 0 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 978 5 View

How can I inoculate a lyophilized anaerobic bacteria into the culture medium without an anaerobic chamber?

There are anaerobic gas pak jars and environment providers in the laboratory that provide anaerobic environmental conditions for the growth of anaerobic bacteria. However, there is no anaerobic...

05 August 2024 4,944 3 View

Is there any Indian Company or Startups, from any universiy or IITS, which manufacture Gas Chromatography instrument , i want to make a custOmized G?

or we can collaborate

01 August 2024 6,704 2 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Gas chromatography RT detection?

I am working on algal extract to which gas chromatography (Not GC-MS) spectrum I want to discover. My question is can we identify specific compounds using retention time if I compared the RT with...

29 July 2024 8,033 4 View

How does the Retention time effect the Biogas Production?

List down the various factors responsible and how does this effect the overall biogas production when it is related to Hydraulic retention time of the digester based on the feedstock?

27 July 2024 4,800 4 View