How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to use the results of Co-IP for protein quantitative difference calculation?

I did a Co-IP MS with two samples and got the LFQ data from MaxQuant, and I wanted to normalize it by an internal reference protein. After I divide the LFQ of the other protein by the LFQ of the...

18 January 2021 5,419 4 View

Does anybody have the recipe for making a home made R electroporation buffer for Neon transfection systems?

I tried the recipes below in two cells lines: 1.DPBS 2.DPBS+MgCl2(1mM) 3.DPBS+Sucrose(250mM) 4.DPBS+MgCl2(1mM)+Sucrose(250mM) 5.R Buffer (Neon) the results showed that R buffer is the best one in...

06 January 2021 6,776 1 View

How to Draw Crystal Structure from powder XRD?

Hi, I would appreciate if anyone can recommend on the process of drawing crystal structure from observed powder xrd diffractogram and if there is any suggested software to work on.

05 January 2021 3,517 3 View

Why mass flowrates of atoms at the inlet and outlet of a reactor are not conserved (CFD with chemical reactions, species model - eddy dissipation)?

Hi, guys. Thanks for reading this question. I am modeling a reactor (steady, RANS). CH3OH and O2 go into the reactor via inlet (a jet). After reactions, species leave the computational domain...

08 December 2020 7,362 13 View

Is the pH value will affect the calculated overpotential in OER process by DFT?

27 November 2020 1,456 2 View

How to transform this implicit FDTD iteration equation into the matrix equation?

11 October 2020 9,042 1 View

What is the best way to evaporate a large volume of aqueous solution quickly?

Let's say I have 100 mL of an aqueous solution and I wish to reduce the volume to 5 - 10 mL. What's my best option? - Rotavap is ruled out because we do not have a vacuum pump that can create...

09 September 2020 2,534 8 View

Bugs in mouse genotyping?

Hi, I am genotyping newly constructed trangenic mice knocking down target gene. I have got F1 generation from F0. And DNA examination indicates that the target DNA fragment has been excised. The...

27 April 2020 5,450 3 View

Will there be a large temperature gradient in the cross-section of a steel member under fire?

I have been working on the behaviors of steel structures at evaluated temperatures. We all know that heat can be easily transferred through steel. So, in real cases, will there be a large...

19 March 2020 1,748 5 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How to make fractions of chloroform extract of plant, using seperating funnel?

28 February 2021 8,466 2 View

Bought HUVEC from Invitrgen.need to revive it.expected it is cryofreezed in DMSO.Do I need to remove the DMSO for plating the cell for the 1st time?

After I cryofreeze the cell do I need to remove the DMSO for culturing the cell for next passages .

28 February 2021 7,738 3 View

POlymer+DMSO solution and moisture??

What could be the reason of moisture at the sides of Vial when I am preparing my polmyer+DMSO solution for membrane fabrication? What etiquettes I am possibly missing here?

28 February 2021 6,516 5 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

How to identify what type of fillers are in a polymer?

Hello everyone, I have some PHAs blended with fillers and nucleating agents, yet I don't know what kind of fillers or nucleating agents. The producer has shut down and there's no way to get in...

24 February 2021 1,356 8 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View