What information can be obtained from a 3D scan in fluorimtric assays?

I have performed 3D scans for fluorescence studies, which consist of contours at the emission wavelength. how to draw useful information from these 3D maps and to understand the dynamics of the...

04 May 2019 8,959 4 View

Is it possible to determine the porosity behaviour of colloidal particles in solution phase or in the form of film?

Actually, the trivial techniques meant for the pore size determination (BET, BJH) cannot be applied for the inquired systems, but I wish to know the porosity trend (whether meso/macroporous),...

08 September 2018 9,104 3 View

Which technique can be used for separating the organometalic powdered catalyst from the organic reactions?

I have prepared a supported catalyst, which is implied for catalyzing certain organic conversion. The catalyst along with reacting precursors are kept under stirring conditions in order to...

06 July 2018 4,205 5 View

How to decide whether the synthesised nanoparticle system is alloy or multimetallic (bimetallic and trimetallic of noble metals)?

Which technique can be used to clarify whether the individual metals are homogenously mixed or are arranged in the bimetallic or trimetallic nanoparticle array?

06 July 2018 8,808 3 View

Do nanomaterials also show the Raman spectra, or just enhance the signal of the materials adsorbed on them?

I want to inquire whether nanomaterials merely act as the substrates for some molecules which are to be analyzed, or they themselves show lines in Raman spectroscopy. For reference, an image of...

06 July 2018 2,626 2 View

Can we use another working electrode for SWASV, instead of thin film mercury electrode?

Usually dropping mercury electrode or Hg modified GCE is used for stripping voltammetry, since it is a conventional or standard process, therefore is it possible to use GCE modified by some other...

02 March 2018 437 0 View

How does the contact angle of a thin film effects it's catalytic efficiency as a heterogeneous electrocatalysts?

I mean if the material of the film is such that It is hydrophobic with high contact angle value, then whether it lowers the catalytic performances of the film as electrocatalysts in aqueous...

08 September 2017 2,866 3 View

How to calculate the number of electron transfer in the oxidation of amino acids using electrochemistry?

05 June 2017 8,298 2 View

How to characterise the wet gel beads?

how to analyse contents in gel beads using HRSEM, EDS and FTIR, as wet gel bead is not preferred for these sensitive instruments?

31 December 2016 2,335 1 View

How to characterise the enzyme immobilised in gel beads?

31 December 2016 6,928 2 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How do I calculate absorption coefficient of my thin film if I dont know the thickness? Or how can I calculate the thickness of my sample?

I have done Uv-vis characterisation of my thin film and have received absorbance and transmittance data. Now I want to calculate the absorption coefficient but I dont know the thickness of my...

21 February 2021 7,148 8 View

How to construct different filler shape in MD simulations?

Is there any way to construct different initial filler shapes like triangle, square, rectangle, pillar, and tube in any simulation software.

20 February 2021 1,750 1 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

What is the reason film thickness increased?

what is the reason film thickness increased when increased doping concentrations give some reasons The measured film thickness is 156, 282, 394, 548 and 681 nm for 0, 1.5, 2.5, 3.5, and 4.5 wt....

17 February 2021 8,987 5 View