Liposome sample preparation - TEM and SEM
Dear Ayshwarya Ravikumar ,
you may have a look at the answers of a similar question of the Q&A section of RG:
https://www.researchgate.net/post/Whats_the_best_sample_preparation_to_investigate_liposomes_in_a_TEM
and also the following paper may help:
Chapter Imaging of Liposomes by Transmission Electron Microscopy
See also:
https://www.protochips.com/wp-content/uploads/2017/10/app-drug-delivery.pdf
and the section 'TEM analysis*)' (page 560) in:
Article AFM, ESEM, TEM, and CLSM in liposomal characterization: a co...
*) and references therein
Good luck and
best regards
G.M.
Do you have cryoTEM or room temperature TEM?
For room temperature TEM, you need to do negative staining.
For cryoTEM, you need to plunge-freeze your samples (negative staining is not required).
Before you load samples on the grids (for both cryoTEM and room temperature TEM), perform glow discharge on the grids.
Liposome preparation
17 January 2024 9,326 0 View
During MOF synthesis, pre-calculation of organic linkers with metals selection should be done In the ab initio method (or any other software) to get the exact product, is that a necessary...
15 January 2024 3,045 2 View
Small angle X-ray scattering-Liposome
10 January 2024 9,416 0 View
Liposome XRD-SEM
02 January 2024 6,803 5 View
Liposome-XRD analysis
30 December 2023 8,865 3 View
Lipid Vesicle preparation
28 November 2023 7,405 2 View
Liposome
28 November 2023 8,604 4 View
X-ray diffraction
28 November 2023 3,561 3 View
I have been trying to amplify one of the gene by PCR and I have optimised the conditions for the same and have got an amplicon. To confirm if the amplicon is my desired gene, I am using PCR...
27 October 2023 5,720 18 View
CFU statistical analysis
15 May 2023 1,016 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...
07 August 2024 5,343 2 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
After immunohistochemistry of previously fixed in PFA and EtOH and then frozen 20 μm sections of zebrafish brain, DAPI staining is very weak (right) compared to the same sections stained without...
05 August 2024 9,637 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View