How to obtain the value of base flow from SWAT model output?

More Sonam Sandeep Dash's questions See All

How to form the state space model of SMIB with Power Electronic Load?

I am working on a small signal stability analysis of a power system on a power electronic load. The power electronic load is modeled as a voltage-dependent load and has the relation attached in...

26 June 2024 2,496 1 View

How can we model Power Electronic Load for carrying out small signal stability analysis?

Currently, I am working on modeling power electronic loads to perform small signal stability analysis. Anyone researching the same area can help me, as there is limited literature on this area. Or...

16 May 2024 5,468 2 View

Problem with beta galactosidase staining assay: X-gal crystals in staining solution?

Hello, I'm conducting a beta galactosidase staining assay for my fibroblasts using X-Gal. I dissolve X-Gal (stock 50mg/ml prepared in DMSO) in the staining buffer at a final concentration of...

25 March 2024 8,799 3 View

Why oscillation frequency less than 1 Hz is termed as inter-area mode and frequency between 1 -2 Hz is termed as local mode of oscillation?

mode of oscillation is classified as stated in the question. I would be grateful if someone can share the literature about it.

17 March 2024 1,846 2 View

If OIBs are uncommon during Archean due to higher melting degrees, why Carbonatites are found during Archean?

The absence of Ocean Island Basalts (OIBs) in the Archean rock records is commonly attributed to the higher melting degrees associated with mantle plumes. However, this explanation raises...

14 March 2024 2,195 1 View

What is the best method for endophytic bacterial isolation?

Mostly bacteria living inside plant roots.

14 March 2024 4,602 0 View

Oscillation frequency of induction motor load in power system stability studies?

Hi, I am carrying out a small signal stability analysis of a power system with an induction motor (squirrel cage) as the load. I am interested in investigating the frequency of oscillation and...

11 February 2024 3,583 0 View

Why number of states does not get reduced when power system stabilizer is deleted from the Model developed in MATLAB/Simulink?

I am working on the small-signal stability of the SMIB system. I want to find the oscillation frequency and damping ratio without and with the power system stabilizer. When I removed the PSS from...

07 February 2024 1,401 0 View

Counterpoise (BSSE) Correction for more than 2 fragments?

What is the correct way to calculate the BSSE correction for a molecule having 3 fragments? Please see the attached image for details. I know the values are pretty close but still I would love to...

25 October 2023 3,990 1 View

Can I use TRIX index for coastal lagoon using DIN and PO4 instead of TN and TP?

Can I use DIN and PO4 in the given formula : The trophic index (TRIX) used in the present work has been given by the following formulation (Vollenweideret al.1998): TRIX = [log(Chla∙ (D%)O2 ∙ TN ∙...

26 September 2023 432 1 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out?

Can we patent a process flow diagram developed using a process simulator but no actual cases is carried out? For example consider a process for certain product manufacture where a new process flow...

31 July 2024 781 1 View

Kishor Gharde

The output file of the model in text rich format will gave the base flow, and all related output in single file. pl check the short form of results.

Sonam Sandeep Dash

Which column gives the value of base flow?

Michael G. Sunde

The baseflow is recorded in 'output.sub' in the GWQ field. The values for your sub-basins must be area weighted in order for them to be meaningful.