How to model shear walls with and without coupling beam using ANSYS Mechanical APDL?

Solomon Getachew Wondimu @Solomon-Wondimu

23 May 2024 0 5K Report

ANSYS Mechanical APDL is one of the numerical simulation software.

Badges
Science topic

More Solomon Getachew Wondimu's questions See All

Can you share me how teacher education is managed in your respective national educational system?

I feel that the practice in teacher education in my country is below the expected performance level due to very poor management system. Hope I will learn something from your experiences.

02 March 2021 1,516 4 View

Could you please share your experience with me on the type of 96 wells plate for MIC determination: Treated Vs Untreated and Round-Vs Flat-bottomed?

I am working on the MIC determination of various antibacterial agents (both water-soluble and- insoluble) against S. aureus, MRSA, and S. pyogenes. Some guidelines recommend using round-bottomed...

17 February 2021 7,029 3 View

How to measure the concentration of a labeled protein with no tryptophan or tyrosines?

Hey I'm trying to measure the concentration of a protein I've purified and then labeled with Atto 647 flourescent dye. The protein has no tryptophans or tyrosines (although does have...

04 February 2021 4,482 4 View

Do you recommend competency based education as an approach to inculcate the 21st century skills?

As you all know, the 21st century skills require higher order thinking. So, do you recommend CBE as a means to realize such kinds of skills?

05 October 2020 7,684 12 View

How to implement lower partial moment of order 1 for given stocks in excel sheet?

I am working on portfolio optimization using lower partial moment of order 1, can someone help me how to implement LPM-1 in excel sheet using "tau" as my threshold value as 0.00% and order (n) as...

05 July 2020 2,510 1 View

Hi guys! I am currently doing research on singularly perturbed time delay parabolic problems. I need your help on MATLAB code for large time delay?

I need help from you who do have a MATLAB code for large time delay. Also, I prepared hybrid scheme for solving singularly perturbed time delay parabolic problems with Robin boundary conditions,...

21 March 2020 6,986 3 View

Hi Guys, I am doing a meta-analysis of fertilizer response studies (eg. Effect of different nitrogen rates on yield). How to enter data in RevMan?

How to enter the different fertilizer rates (including a control) in RevMan?

02 March 2020 5,309 2 View

Does homogeneity test prove missing data replacement was good enough?

I have carried out linear interpolation to fill missing monthly rain fall data, and carried out homogeneity test using standard homogeneity test for the annual and seasonal time series from the...

28 December 2019 758 3 View

Why do i need to combine materials characterization technique when investigating the Microstructural morphology of metals?

That is why do i need to do SEM after i have done TEM?

16 June 2019 8,733 4 View

What is the source of positive current in the cathodic potential region?

I am working on hydrogen evolution. In some of my samples grown/sputtered on nickel foam and carbon cloth substrate, I found a very high positive current in negative potential as shown in the...

07 June 2019 5,940 3 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View