I need to add FBG sensors in order to model the delamination in composite materials? Does anybody have any idea how can I do that?
Try the following links:
https://www.google.com/url?sa=t&source=web&rct=j&url=https://www.ndt.net/article/ewshm2012/papers/tu4c4.pdf&ved=2ahUKEwi2tMmm7bbtAhXY83MBHU3PBxIQFjAAegQIARAB&usg=AOvVaw3TZ7d9N-4vIN5Jy_7kL6JI
https://www.google.com/url?sa=t&source=web&rct=j&url=https://www.sciencedirect.com/science/article/pii/S1877705812026185/pdf%3Fmd5%3D71355bef62ddeb3bd69f6cfb0acf2548%26pid%3D1-s2.0-S1877705812026185-main.pdf&ved=2ahUKEwi2tMmm7bbtAhXY83MBHU3PBxIQFjAEegQIDRAC&usg=AOvVaw2IPO0ERUa1FjiC2FX891RH
Best regards.
@ S M Anas
Thank you. Do you have any resource to model in abaqus?
these research articles may help you
also, check this article
Hello friends, I could not find any template for this journal which stated that it should be doubled column. Any help? Thanks
13 February 2023 4,258 5 View
Hello I have a question regarding the damage mechanics and strength prediction. Could anybody explain me the exact difference between damage mechanics and the failure criteria? For instance,...
07 June 2021 1,285 9 View
In order to input conductivity for a composite material in abaqus should we give orthotropic conductivity in the material module? If so, is it found experimentally?
24 January 2021 4,938 3 View
Hi, Does anybody have any idea whether we need to give laminate properties or lamina properties while modelling the composite as a solid model? I modeled a composite using the solid and material...
08 January 2021 1,408 10 View
Hello, Does anybody have any idea what the parameter shown in thi figure below is? It is in the temperature boundary condition. I applied pre-defined boundary condition (initial ambient...
07 January 2021 8,057 4 View
I have two sets of numbers. If the mean and standard deviation for one set are near to another does it mean the sets are somewhat equal to each other?
20 October 2020 6,460 3 View
Hello, Consider we have a finite element model with two elements and each element has a line with slope. consider again we run that finite element with two different theories. Therefore, for each...
19 October 2020 8,006 1 View
Hello, One referee asked me a question about one of the papers. Could anybody explain this one for me? I never thought about it The load cell of the Instron was 100KN which is very large....
03 September 2020 496 5 View
Hello, I found a umat code for abaqus analysis which is written in the fortran. There is an expression while starting the code "!DEC$ FREEFORM". As far as I understand, this expression forces the...
01 March 2020 6,995 2 View
Hello, Does anybody know how can I find stress concentration factor around the hole in abaqus for a plate with hole (No crack, but hole)? I read somewhere that is defined as the ratio of the...
12 February 2020 4,050 1 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
need of sensor details or sensor development for this question.
28 July 2024 4,539 3 View
Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...
28 July 2024 8,169 0 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I try to understand the ESP mechanism working. What kind of sensors it has, Is it necessary to modify or boost its mechanical ?
15 July 2024 4,772 1 View
Continuous glucose monitors (CGMs) help patients and doctors make more timely management decisions by monitoring blood glucose levels in real time. An insulin pump provides continuous insulin...
07 July 2024 7,742 0 View
I am very new to the material modelling in GDIS. So, I want to learn how to model a nanostructure specifically core-shell in GDIS.
28 June 2024 5,224 0 View
A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....
25 June 2024 10,154 0 View