How to model a ring magnet in ANSYS 3D ?

Gokul Prassad S @Gokul_Prassad_S

12 December 2016 0 2K Report

I am trying to model two ring magnets in ansys and analyze them to measure the field between them at various distances.

Badges
Science topic

More Gokul Prassad S's questions See All

Can someone give me an example for ESURF command in ANSYS?

i am trying to model air inside a rubber container and check the deformation of the vessel on compression. Kindly help

10 November 2018 309 4 View

How to analyse the force between two permanent magnets in ansys ? can you kindly suggest some journals or videos ?

I am trying to analyse the force between two permanent magnets to study their applications.

11 December 2016 6,061 3 View

Are there any advantages for a field sensor(magnetic field/strength) over a displacement sensor ? Especially in a dynamic application ?

i want to measure the variation in the field strength based on the applied load. Also, i want to compare if it is advantageous over employing a displacement sensor. Especially for unit impulse...

07 August 2016 6,847 1 View

Is the dimension of the magnets directly related to their repulsion ? if yes, kindly tell the relation ?

if there is any formula with the repelling distance or the flux developed with respect to the length and diameter of the magnets

07 August 2016 6,224 4 View

How to apply dynamic load to a quarter car model and obtain results in MATLAB Simulink environment ?

I modeled random roads in MATLAB environment and obtained displacement vs time plots for static loads. When i tried applying dynamic loads, errors start popping up. Is there any available algorithms ?

01 January 1970 3,048 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View