03 May 2016 3 6K Report

Hi everyone , I need to model a moving load in ANSYS. I want to model the movement of a train on a bridge. IS there anyones who can help me with this issue??

More Eduardo Cobo Sarmiento's questions See All
Questio regarding micro/nano particles fabrication ?

I will start to fabricate micro/nanoparticles for growth factor release and I check out a procedure quite nice, however, it is lacking some details and since I don't have much knowledge doing this...

20 February 2021 199 2 View

How do you prepare a standard dilution for qPCR?

I am very new to quantitative PCR and need some help for this technique. For my experiment, I need to perform a quantitative reverse transcription PCR. I extract the RNA from my pellet and...

05 February 2021 9,834 4 View

Can I modify vermiculite or perlite by adding nutrients to control a certain situation?

I need to assimilate a determining condition for the plant. However, I need to ask you if it is possible to change the properties and concentration of plant nutrients in this material like perlite...

04 February 2021 8,616 11 View

What is the half-life of TNF-alpha in vitro?

I'm designing a low-grade chronic treatment with this cytokine and I'm wondering how regularly to change the culture medium based on the half-life of the protein in an in vitro environment....

24 January 2021 5,988 2 View

Which sampling techniques can be used for huge flying insects?

Tropidacris collaris is a grasshopper. Adults, which can reach more than 15 of length, are strong flyers and actually they resemble small birds or bats. Most of the time T. collaris is found in...

13 January 2021 3,735 5 View

Does freezing treated cell pellet at -80C damages them?

Hello, I hope you are all doing well. I have a question regarding my treated cells group. I plan to do western blot and qRT-PCR for my treated cells. However, to save time, I would like to...

06 December 2020 1,390 5 View

Why do some primers have transcript variants/unintended templates for different genes?

Good day, I hope you are all doing well. I was designing primers for Caspase 9 and sometimes, the designed primers in NCBI have transcript variants for the same gene (Caspase 9) but at the same...

05 October 2020 352 3 View

Do I need to design forward and reverse primers within an exon region for QRT-PCR?

Good day, I hope you are all well. I am new in designing primers for quantitative reverse transcription PCR. I am using NCBI to design my primers and my question is: Do I have to design my...

04 October 2020 7,678 7 View

Why is my molecular rotor displaying a bathochromic shift in toluene compared to MeOH or EtOH?

Hello, I am studying the photophysical properties of a molecular rotor which unexcpectedly, shows a lambda(max, absorption) = 565 nm in toluene, but a lambda (max, absorption) = 540 nm in MeOH...

15 September 2020 7,830 3 View

Animals - Special Issue, "Learning Theory Applied to the Welfare of Animals", looking to submit?

Dear Colleagues, Please see the following link and information for more details. If you are thinking about submitting, please feel free to reach out to me directly here or at...

09 September 2020 6,361 1 View

Similar questions and discussions
MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close