How to measure carbon estimation without destructive methods in plant?

More Mukesh Mali's questions See All

Can the problems of overfitting be solved without cross validation?

For an overfit data set the cross validation error will be much bigger than the training error. Is it true or false?

23 February 2021 3,616 2 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View

Where to find data set to carryout learners analytics?

I need learners data set to carry out diagnostic and predictive analysis

22 December 2020 1,782 2 View

How to make CAB/PMMA polymer blend?

I need to synthesis CAB/PMMA polymer blend. Please tell me how to do it.

19 October 2020 9,843 3 View

Why is there splitting in Raman bands with symmetry lowering?

I have encountered the splitting of Raman bands (especially G band in G+ and G- peaks) while characterizing graphene under strain using Raman spectroscopy.

02 September 2020 6,756 3 View

Which phenomenon is responsible for showing unusual PL Spectra of a 2D material based hetero-structure in view of inter-layer coupling?

Shift in PL emission peaks of SL- WS2 and SL-MoS2 is observed individually under applied strain but due to inter-layer coupling WS2/MoS2 hetero-structure does not show Excitonic behaviour...

27 August 2020 4,439 3 View

Compression deformation in Ansys has errors and not get solutions?

I am doing compression if High Entropy Alloy in Ansys19.2. I tried a lot of ways but it does not converge. It explodes the specimen.and show errors as well. Herewith I have attached the screenshot...

13 August 2020 6,229 1 View

Which signal (Pulse or DC) is often used for read and write operation in a SRAM memory cell.?

For the read operation, the WL will be at logic high (Vdd or let 1V) and initial condition at internal nodes (let Q and QB) are 0 and 1 V. The BL and BLB are also precharged to logic high....

14 July 2020 9,538 8 View

How to calculate Local Centrality ?

Using the networkX package i have calculated different centrality index over node. But during this calculation cutoff distance is not specified. So how to calculate closeness and betweenness...

10 March 2020 475 1 View

Not Getting Clone/Colony with NEB HiFi Assembly Cloning Kit ?

In short, I am trying to get a clone of 1664 bp insert in a mammalian expression vector (Size of vector is 6250 bp) by using NEBuilder HiFi DNA assembly Cloning kit with commercial Comp cells...

06 January 2020 541 3 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View

How can I assign a velocity along one direction to CO2 molecules in a molecular dynamics simulation using GROMACS?

Dear all, I am trying to perform a MD simulation about the interaction between CO2 and a polymer. I create my model, solvate it and perform the NVT and NPT equilibration. Now I am not able to...

26 February 2021 10,014 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

CGA 300 Regulator for CO2 cylinder?

Has anyone ever tried to deliver CO2 with a CGA 300 regulator? I know that a CGA 320 regulator is standard for CO2. The issue is that I currently do not have any free CGA 320 regulators. I also...

25 February 2021 3,292 3 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

How to clean up TEM grid with plasma cleaner?

I need to clean the hydrocarbon contamination on the carbon substrate of TEM grid. However, I heard that substrate could be broken by the powerful plasma. My substrate is pure carbon, with ~3nm,...

23 February 2021 3,262 5 View

What are some underexplored theories and concepts in Activated Carbon as A Water Filter?

Hi, me and my team mates are currently planning to pursue the topic of Activated Carbon from Coconut as a Water Filter. And we would like to ask for your suggestions and knowledge on what specific...

22 February 2021 6,569 3 View

What are some underexplored theories and concepts in Activated Carbon as A Water Filter?

Hi, me and my team mates are currently planning to pursue the topic of Activated Carbon from Coconut as a Water Filter. And we would like to ask for your suggestions and knowledge on what specific...

21 February 2021 7,561 4 View

What properties of water shall be analyzed and evaluated to test the effectiveness of activated carbon?

I would like to ask what other properties of water (pH and such) shall be analyzed and evaluated to test the effectiveness of activated carbon from filtering the contaminants present in the water?

20 February 2021 9,422 8 View

Damien Ertlen

You could check near infrared or infrared spectroscopy. It is non-destructive and can be used on field with a fiber. Sincerly

Mohit Kumar

One of the ways is to estimate plot level biomass and then correlate them with satellite observed values.

C.P. Rahangdale

Dear, have a look at these pdf attachment of manual for non destructive method.

Good luck