How to match results from based paper and Ansys Workbench in modeling piezoelectric?

More Hossein Abbaszadeh Mobaraki's questions See All

How to model Supercritical water gasification (SCWG) process in Homer software?

Hi everyone How to model Supercritical water gasification (SCWG) process in Homer software?

25 February 2021 4,075 1 View

Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software?

Hi every one Is it possible to define biogas as a fuel in the reformer process(scwg) in Homer software? Biogas fuel is not available in the options thanks

23 February 2021 6,518 3 View

How can I find the thermophysical properties of high temperature microencapsulated phase change materials (MPCM)?

Hi everyone. I am looking for a high temperature MPCM. More specifically, I need the thermo physical properties of a microencapsulated phase change material with the melting temperature between...

14 February 2021 3,606 2 View

Can explain this diagram to me, is this the average consumption curve for one day or the total consumption of days in a month summed up in specific?

The hourly load curves of the selected household in each season are shown in Fig. 28. Figure 28 shows the demand for electricity in four months on an hourly basis. Can you explain this diagram to...

08 February 2021 657 16 View

How can I find eddy size distribution in ANSYS Fluent?

Hi everyone, I'm simulating a 3D turbulent pipe flow using the SST K-W turbulence model in ANSYS Fluent. Is there any quantity among the postprocessing quantities that represent "eddy size" or...

01 February 2021 731 1 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

What is the gradient thermal annealing (GTA) process?

Hello to all What is the gradient thermal annealing (GTA) process?

06 January 2021 7,740 2 View

What is the difference between organic perovskite solar cell and inorganic perovskite solar cell?

Hi everyone What is the difference between organic perovskite solar cell and inorganic perovskite solar cell? Thanks

01 January 2021 4,310 6 View

How to measure both Sulfites and Sulfates Ions In water?

Could you please help me to know a very simple method to measure the amount of Sulfite (SO3) and Sulfate (SO4) ions in the water? (titration preferred)

27 December 2020 9,350 4 View

Is it rational to identify differentially expressed genes from tissues (in silico) and examine gene expression on the associated cell lines (wet lab)?

I am going to evaluate the gene expression levels in the MKN45 cell line (gastric cancer). Before that, I want to identify critical differentially expressed genes obtained from tissues available...

20 December 2020 3,774 6 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Ijaz Durrani

Dear Dr Hossein--- please have a look at the following useful links:

Article Analytical, FEA, and Experimental Comparisons of Piezoelectr...

and

Hossein Abbaszadeh Mobaraki

I have checked the papers you mentioned @ljaz Durrani. As stated before, my modeling has a minor problem causing error. I am eager to find it

OK , Dr Hossein It is the spill over effect, I think! have a look at the following useful links:

Article Research on Spillover Effects for Vibration Control of Piezo...

https://worldwidescience.org/topicpages/c/compression-loaded+laminated-composite+cylinders.html

Regards--