How to make 2mm ? - FAQS.TIPS

24 September 2021 1 6K Report

Is it made by drawing

USING THE FORWARD EXTRUSION METHOD, AND IT IS SO EASEIAR TO CALCULATE THE NUMBER OF STAGES BASED ON THE MECHANICAL BEHAVIOUR.

Badges
Science topic

Similar topics
Correction

More Py De's questions See All

RNA later for the preservation of RNA in fecal samples at room temperature for one day (37°C)?

I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...

06 August 2024 1,367 3 View

How to develop an academic literacy program for engineering at the higher education level?

Information literacy in higher education integration with curricula engineering

04 August 2024 5,368 3 View

How can i generate a CRISPR knockin mutation zebrafish model with a reporter?

Hey! I aim to generate a transgenic knockin zebrafish line that mimetizes a genetic condtition that leads to a certain disease on human. To do so, I need to insert a codon for mutagenic aminoacid...

14 July 2024 6,240 0 View

What should be the best Lumens range for T8 (120cm) full spectrum LED lamp tubes?

Please (for Arabidopsis), what could be a good Lumens and color range (Kelvin) range for full spectrum LED lamp tubes size T8 (120cm) for each shelve measuring 130x50 cm (length x width) and 60 cm...

11 July 2024 6,078 1 View

Cross Attention in Transformers: Standard applications of the same ?

What are the standard applications of Cross Attention in Transformer Architectures ?

09 July 2024 9,310 2 View

Time Series Analysis: Has Recurrent Neural Networks (RNN) ever been used on Time Series Analysis ?

Are there standard RNN architectures been applied for Time Series Analysis, forecasting and anomaly detection problems ?

30 June 2024 3,169 8 View

LSTM on Time Series: Has LSTM architectures ever been applied to Time-Series Forecasting ?

Have we ever used LSTM architectures on Time-Series Forecasting and Analysis, and gotten a decent result ?

30 June 2024 6,924 3 View

What could be causing these smears in my PCR electrophoresis gel?

I am new to running PCR gels. I loaded this gel and I thought it was fine, meaning I saw/felt no apparent punctures or spillovers to neighboring wells (see picture 1). When the gel started to run,...

30 June 2024 4,107 4 View

What are the typical applications of Large Vision Models (LVMs) ?

Where are large vision models typically used ?

25 June 2024 4,113 0 View

Are there standard libraries/frameworks for doing RLHF for training LLMs ?

When it comes to Re-inforcement Learning with Human Feedback, are there standard libraries/frameworks for training LLMs ?

25 June 2024 1,121 0 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

How to remove aluminium oxide from powder ?

I synthesise intermetallic compounds through nickel and aluminium powders. But the pure powder after synthesis is difficult to obtain. Especially the presence of aluminium oxide very seriously...

01 July 2024 4,030 3 View

Can I use aluminium acetate basic instead of aluminium acetate to synthesis iron oxide nanoparticle through hydrothermal method?

My idea was to prepare discal shaped iron-oxide using Al3+ metal-ion mediated solution to regulate the morphology of of my nanoparticles, but most literature uses aluminium acetate and not...

22 June 2024 6,136 2 View

How to achieve optimal bonding strength at the wire-bonding process?

Hello everyone, without going too much into details, my thesis is about improving the bonding strength at the wire bonding process. I should focus on laser pretreatment of the substrate. Has...

17 June 2024 366 1 View

How can I simulate magnetic field of a wire in Cst suite learning edition?

Recently I have an assignment about Simulating magnetic field and I will need the result to derive it. But when i downloaded it i noticed that i am just a new to Simulation software. So can anyone...

04 June 2024 1,270 0 View

What are the effects of the copper wire diameter used in a DC electromagnet winding on the winding temperature that occurs during operation ?

Let's consider two windings containing thin diameter wire(0.3 mm) and thick diameter wire(4 mm). These windings operate under the following conditions. 1- The same power is applied. 2- They have...

22 May 2024 7,255 5 View

How to remove the oxide formed on the Ti6Al4V due to the temperature rise by wire EDM without using polishing?

Hello everyone, I need assistance to remove the oxide formed on the Ti6Al4V. During the cutting by wire EDM, oxide was formed on the surface of the alloy. Since the micron level features are...

22 May 2024 5,871 4 View

What is the best method to enhance the surface hardness of cutting tools made from SPK steel?

SPK tool steels are used for cutting wires made from low carbon steels. We are searching for a cheap and effective method for increasing the cutting characteristics of the cutters.

14 May 2024 4,948 0 View

What happen if austenite finished temperature of Niti alloy's wire is lesser than body temperature (37 deg celcius) for wired stent applications?

Suppose austenite finish temperature of Niti alloy wire A is 25 deg Celsius and Niti wire B is 35 deg Celsius. Which one is best recommended for Biliary stent application and why?

29 April 2024 7,585 0 View

Hi, can anyone help me analyze some metallographic images of low alloy steel?

ER70S-6, Wire arc additive manufacturing, low-alloy steel

25 April 2024 7,086 0 View