Hi, I'm using the Hayes Process model 15 but confused with the judgement and interpretation showed in the following picture:
If the IU(the mediator)is no longer significant, will it influence the moderated mediation effect?
Check if our papers help you:
Why methanol and sulphuric acid, used in the analysis of polyhydroxyalkanoates (PHA) methyl esters by GC-MS? Additionally, why do we typically use non-polar solvents in GC-MS?
22 July 2024 1,210 2 View
I'm trying to create a new substance. Are there any important considerations when fabricating with CVD? For example, lattice constant If you have any such considerations, please let me know.
15 July 2024 9,359 0 View
I need tips for isolating Ralstonia solanacearum from eucalyptus. I have used some methods, such as isolating from root exudates, but it didn't work. I also tried indirect isolation from macerated...
02 July 2024 9,807 3 View
Hi, All, I am relatively new for exosome isolation. I used an izon column 70nm to isolate exosomes from differentiated neural cells, but the concentrations were pretty low after NTA analysis (I...
01 July 2024 2,558 0 View
I wonder the tendency of coefficient of thermal expansion (CTE) of polymer which has different chain structure. In my opinion, CTE will be higher when the polymer materials has high interaction...
30 June 2024 570 5 View
research on mental health and ethnicity
18 June 2024 3,958 0 View
I know that I need to calculate lattice mismatch to determine which substrate a particular material can grow on. However, no matter how much I searched, I could not find a way to calculate the...
03 June 2024 6,730 2 View
How small should the lattice constant mismatch be when epitaxy of a material? and in case of A+B -> C, is C the material whose lattice constant must match that of the substrate? Did I...
29 May 2024 8,155 4 View
From bolztmann equation to Fulid model or Drift-Diffusion model, What assumption we made? such as maxwell distribution or local thermal equilibrium.
08 April 2024 1,968 1 View
I need to run CVD parylene deposition onto gold wires. How can I clean the gold surface before coating to achieve good adhesion? Thanks a lot!
07 April 2024 4,537 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
i am facing the difficulty to find the right and latest topic for my thesis. i searched and read hundreds of articles but i couldn't find the right one. what can i do I'm really confused.
02 August 2024 1,323 8 View