I want to create a flowsheet for a steam explosion in ASPEN and I want to put a piston pump in the inlet having a flowrate of around 1 kg/hr and operating at a pressure of 45 bar. I am new to ASPEN, so how can I show this data as a piston pump?
I have seeded HeLa cells in a calculation of 10000 cells per well in a 96 well plate. Then I went for treatment in the next day. Then at last, I added 7ul of 5mg/ml solution of MTT reagent into...
12 June 2024 1,460 3 View
I have done an RMSD validation for such protein by docking the two ligands one by one, but each docking results in large RMSD value compared to the reference.
22 January 2024 2,054 5 View
Hello everyone, I am performing western blot (SDS-PAGE) for the phospho-mTOR protein, molecular weight 289 KD. I am using 6% resolving gel for it. I kept the transferring time around 4 to 6 hours...
18 January 2024 1,061 1 View
I am trying to extract lipids using water as solvent. After extraction followed by centrifugation, I did not obtain any oil layer. Instead the supernatant was milky white, which I think might be...
30 October 2023 9,151 1 View
Steam jet ejectors are not present in the built in models of Aspen Plus. How to add a steam jet ejector in Aspen Plus. Can it be done by the combination of two models or are there any other...
18 October 2023 5,200 1 View
Usually MED is accompanied by a steam ejector or compressor. How is the subatomic pressure maintained inside the effects?
17 October 2023 4,447 3 View
Whether the lifetime will increase or decrease w.r.t to a system which has no confinement? Furthermore, let me know, how I can use PCM model and extract the Raman profile for a particular range...
12 October 2023 6,795 1 View
Electrochemical active surface area (ECSA) from CV or EIS
16 September 2023 9,729 4 View
I took an IRF using deionized water in the TCSPC system, in which the decay profile showed multiple peaks instead of smooth exponential decay.
10 July 2023 5,232 4 View
I want to perform some DFT study for which I require the CIF file. I searched COD and materials project, but it's not there.
24 June 2023 8,116 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...
06 August 2024 5,023 1 View
Global ‘Weather’ has stopped, as ‘aqua thermionic instituted by the ‘Global thermo atmospherics has instituted global thermodynamics of 120º C + and thus all waters are, or have boiled into a...
06 August 2024 8,716 0 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Hi, i would like to simulate an absorption process in Aspen Plus. I want to use the NRTL model und would like to add some individual Henry coefficients. Is that possible and how?
05 August 2024 2,333 2 View
TEP presentation caption (The Environmental Project) Re: Why should Washington’s DC, or any country government point of location think of as nowadays of as to being 'tomorrow as to come! if it...
03 August 2024 2,484 1 View
A typical reforming section in a large-scale Haber-Bosch process (Figure 1) comprises two reactors. A mixture of methane (CH4) and steam (H2O) is fed into a primary reformer to produce syngas via...
01 August 2024 7,051 5 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,380 0 View