How to add different colors to a pseudo- colour image using Fiji ImageJ?

I have a grayscale image of which the original RGB image was formed by combining Green and Red channels which represent different types of cells (live/dead). Splitting the channels in RGB mode is...

11 March 2020 1,616 3 View

How do I force material studio to stop or break the current command in progress before it crashes?

Something equivalent to Ctrl+C in Matlab to break the code. Thank you in advance.

22 January 2020 4,545 2 View

Can anybody tell me how to specify chemical reactions in FLUENT material database for FLUENT CFD Simulation of CO2 dissociation in thermal plasma?

Fluent Software

12 October 2017 6,229 2 View

Why does the peak current of a molecule increases after the addition of protein?

20 January 2017 5,664 1 View

Dear Colleagues, Who is the Piper expert in the world?

12 April 2016 9,784 8 View

What is the effect of fly ash in fly ash-cement mortars related to normal consistency, setting time and workability?

Construction materials

16 September 2014 813 8 View

Does anyone have any knowledge on gel extraction and DNA purification?

During DNA gel purification using a centrifugation technique, I accidentally centrifuged the sample at 1300 rpm instead of 13,000 rpm. What will be the consequence? The gel along with DNA weighed...

02 July 2014 1,239 2 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Does Napabucasin soluble in dichloromethane and in ethanol?

I need to prepare a solution of Napabucasin (inhibitor of cancer cell stemness) in dichloromethane. The drug is expensive, so maybe somebody already tried to do it. If it is soluble, what is the...

02 March 2021 9,945 3 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

What is the most suitable resuspension buffer for TCA/acetone precipitated protein?

I need to extract protein from fermented carbon sources for Bradford assay. Most researchers experiencing insolubility of pellet in resuspension buffer. Please assist me to select most suitable...

26 February 2021 7,129 3 View

EMSA troubleshooting. Protein-DNA complex not migrating, cold probe lane with multiple bands. Can anyone help?

I'm running an EMSA to show the DNA binding activity of recombinant proteins versus the Wild type. Previous assays run by my research group using a different test system show the protein-DNA...

24 February 2021 8,325 1 View

Do you kow of any database containing data on retention time, log P and polarizability for a large number of molecules?

Hi, I am a chemistry undergraduate doing my dissertation project on HPLC. In my project, I need to predict the HPLC retention time of 20 aromatic molecules, the calibration set. To do this I will...

24 February 2021 2,602 1 View

How to seperate PEG-4000 from aqueuse phase ?

Hello everyone , Please tell me if It possible to seperat POlyethelyn glycol -4000 from an aqueuse media by other ways rather heating . I have tried salting out by electrolyte solution to...

22 February 2021 7,285 5 View

Could you please share your experience with me on the type of 96 wells plate for MIC determination: Treated Vs Untreated and Round-Vs Flat-bottomed?

I am working on the MIC determination of various antibacterial agents (both water-soluble and- insoluble) against S. aureus, MRSA, and S. pyogenes. Some guidelines recommend using round-bottomed...

17 February 2021 7,029 3 View

How to analyse monosaccharide compositions from soluble fiber?

I have tried to hydrolyze the sample using 2 M TFA at 100C for 24, 48 h and 120C for 2 h. From these conditions, the HPLC results showed that peaks were not separated into monosaccharide. I found...

17 February 2021 5,230 1 View