How to grow bulk high quality InSb and GaSb crystal for the Infrared device applications?

27 September 2014 0 3K Report

For infrared and optoelectronic devices requires high quality crystal. These crystals must be chemically and electrically homogeneously uniform bulk crystals for high device yield. The production of bulk crystal must have large size and low cost.

Badges
Science method

More Dattatray Gadkari's questions See All

Can somebody help me to calculate enzyme activity by HPLC method?

I am working on enzyme and its assay method is HPLC. So I have two things to monitor 1) Decrease in substrate concentration (area under curve of substrate) after specific time 2) Increase in...

07 November 2016 3,080 7 View

Why do infrared devices require high quality crystals?

The bulk of InSb and GaSb crystals grown by VDS have been used for infrared applications. Crystal performance needs to be improved for sensors and detectors.

16 October 2014 823 2 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

Recommendations on homogenizers for RNA isolation?

I will be performing RNA isolation with frozen lung biopsy samples and am in the market for a tissue homogenizer. I am wanting a homogenizer that will fit in a 1.5ml tube. I was looking at the...

24 February 2021 3,623 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View