05 May 2016 1 8K Report

A+B gives C. 

Do we need to find the vapor pressure of A and B first or how??

More Puneet Jain's questions See All
How is gas flow rate and pressure dependent on each other. I have an initial increase in the graph, then decrease and then increase again?

How is gas flow rate and pressure dependent on each other. I have an initial increase in the graph, then decrease and then increase again.

04 May 2016 346 1 View

How a bubble is formed, when gas is passed into water through a pipe?

How a bubble is formed when gas is passed in a bottle of water, through a pipe.  What is critical pressure, atmospheric pressure, gas pressure, etc. in this case. 

04 May 2016 9,347 5 View

For STM imaging of Co2MnSi thin film on Si, what should be the bias voltage and bias current, at which we can measure the surface morphology?

I have deposited thin film of Co2MnSi on Si wafer by RF sputtering. 

01 February 2016 6,636 3 View

Similar questions and discussions
1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Best mask design for metal deposition aiming build a Perovskite solar cell device?

What types of mask designs for metal deposition, to be used in a PVD system, are best suited for perovskite-based solar cells?

31 July 2024 4,835 3 View

Question about water vapor uptake of metal-organic frameworks?

I'm working on the atmospheric water harvesting, and i synthesized MOF by adding some materials into precursor and changing the conditions. (i followed Hydrothermal method) Actually, if MOF is...

24 July 2024 1,515 0 View

Is the zero-zero component of the metric tensor equal to 1 for accelerating reference frames?

Consider the case of negligible gravity but there is an accelerating reference frame. Its origin traces out a trajectory, or world line, seen in some inertial reference frame. The Lorentz metric...

24 July 2024 1,608 15 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

Environmental Impact of the Organic Manure Production Unit?

Does anyone have any case studies on the Environmental Impact of Organic Manure Production Unit? Environmental Impact of a Organic Manure Production Unit Facility is what I studied but...

16 July 2024 5,400 6 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close