How to find gR(t)=normalized shear modulus?

22 August 2020 1 463 Report

I want to use relaxation test data in abaqus. Abaqus wanted terms like gR(t)=normalized shear modulus at time (t) and long term normalized shear modulus to find prony series. can you help me in calculating (gR(t)) from relaxation test data OR any other way to find prony series from relaxation test data

Chitaranjan Pany

pl. see maybe useful

Badges
Science topic

More Irfan Ullah's questions See All

Why the difference between degrees of nonclassicality of the input states is required for nonzero entanglement in the output state of a beam splitter?

By considering two single-mode Gaussian states at the input of a beam splitter, it is seen that the entanglement of the output two-mode Gaussian state depends on the difference between the degrees...

22 January 2021 3,490 3 View

Similarity between these two waveform? Similarity in terms of Shape?

Hi, These are the outputs generated by a system. Green-colored (nr) is desired output, while the system generates Red-colored (nf). I also have a dataset in CSV file. For this waveform, What...

21 January 2021 929 2 View

Which kind of GPC solvent can be used to dissolve both lipid and salt?

I want to find a GPC available solvent to dissolve both lipid (DPPC, 2 mM) and salt (NaCl, 100 mM).

14 January 2021 3,805 2 View

What are the (extrinsic) factors that influence the citation rate of a research article?

Dear RG members, Excluding the (intrinsic) factors such as quality and content of an article, what are the extrinsic factors/predicors that influence the citation rate of a research article? Is...

07 January 2021 3,410 3 View

Hi Everyone. I want to conduct DEMATEL analysis for my survey. Everything is in line except the MAXIMUM MEAN DE-ENTROPY (MMDE) ALGORITHM. Need help ?

I can't find any manual or procedure on how to conduct the MMDE process. It looks like most of the literature has copy-pasted the stuff without any method of how to do to it. Any practical book,...

07 January 2021 1,804 2 View

Does anyone have experience in infecting suspension cells (like THP-1 or K562 etc) by retrovirus?

I am trying to make stably expressing cell line of my gene of interest in Suspension cell line using retrovirus but i don't have recommended protocol. I have searched literature but mostly they...

14 December 2020 8,274 3 View

Hello I have a question about solar cells (perovskite solar cells) modeling in COMSOL?

I have done all optical simulations in RF module, now how can i find generation rate of electrons and holes, secondly how can i use these generation rate in semiconductor module to find further...

11 December 2020 6,652 3 View

Can a mathematical model be added to a paper on bean genetic and diseases manuscript?

10 December 2020 2,300 14 View

Straight chain or Ring peptide for inhibiting a homo-dimer of a 20 KDa secretory protein?

I am designing a small peptide to inhibit a homo-dimer of a small secretory protein (about 20 KDa). I need suggestions on, which option would be better? a straight-chain peptide or a ring-shaped...

03 December 2020 4,145 5 View

Hybridoma stops producing antibodies after thawing from liquid nitrogen?

Dear scholars, Our research is currently involved with hybridoma technology. We have isolated some original clones after fusion and we are preparing the subclone step to find some true positive...

01 December 2020 1,178 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View