Dear all,
I am in search of such an equation or model which can be used to express relative growth rate or growth kinetics of mushroom.
Your valuable suggestion will be highly appreciated.
Regards
Vinod Kumar
Normally for mushroom, biological efficiency is used:
% biological efficiency = (mushroom fresh weight) / (compost or growing material dry weight) x 100%
Hello Vinod,
Could you elaborate on what specifically you are interested in measuring? Vegetative or fruiting body growth? You can find an equation for specific growth rate at: http://www.davidmoore.org.uk/21st_Century_Guidebook_to_Fungi_PLATINUM/Ch04_09.htm
Dear Jake Winiski it is all about fruiting body growth. Not mycilial.
Suppose the electrocatalysis time is 8h
10 August 2024 5,677 2 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...
29 July 2024 3,246 0 View
Purification of gst tagged protein
25 July 2024 1,720 0 View
If you don't understand my question let me know
21 July 2024 563 1 View
I am working on scale development in behavioral finance by undertaking a mixed-method approach using the exploratory sequential design. The phenomenon has diverse meanings in existing literature...
20 July 2024 9,153 11 View
I need to convert Available phosphorus into total phosphorus
18 July 2024 6,799 3 View
Bioinformatics tools like peptide cutter
15 July 2024 6,453 1 View
The burden of obesity is enormous. The greater challenge lies in accurately diagnosing obesity at the right time, reflecting the true increase in visceral fat. BMI may not accurately represent...
14 July 2024 8,771 4 View
How does high humidity affect the growth and development of crops?
10 July 2024 7,258 20 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...
03 August 2024 6,028 4 View
AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...
31 July 2024 9,733 3 View