How to draw Scheme Fig. ?

More M. H. Ashourzadeh's questions See All

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

I have calcined my catalysts without flowing air from the compressed air cylinder will there be any problem with my reaction if i use that catalysts?

FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion

25 July 2024 2,486 2 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

How can I measure arsenic concentration in a patient blood?

I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.

23 July 2024 3,654 2 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

It is possible to conduct a structured written interview for a qualitative study?

In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...

11 July 2024 4,163 4 View

Possible reasons for not getting wake effects in free surface?

Hi, I am trying to simulate a ship in a canal. The top width of the canal is 20m, bottom width is 6m, depth is less than 5m. Ship has a length of 11.7m breadth of 4m, draft is 0.62m. The velocity...

10 July 2024 1,732 4 View

What is Differential-Fed in microstrip patch ant? How it is design in CST studio? What is process and procedure to do Differential-Fed in CST studio?

What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?

08 July 2024 7,464 1 View

How to know the TM/TE modes in antenna design in CST studio?

How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...

08 July 2024 6,609 2 View

What is co-polarization and cross polarization? How can plot it from CST studio?

what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?

08 July 2024 7,869 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

How to report results of Generalised Linear Mixed Models in a journal article?

Hi everyone, If you have written or come across any papers where Generalised Linear Mixed Models are used to examine intervention (e.g., in mental health) efficacy, could you please share the...

04 August 2024 4,130 4 View

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal?

Any idea about 'International Research Journal of commerce , arts and science? Is it a UGC listed journal? Kindly advice

04 August 2024 7,367 3 View

Are authors sowing for scientific Journals to be reaping the benefits? We are charged for publication but we offer free peer review services, why?

As authors and academic writers, we usually prepare our manuscript using our own resources. We submit these manuscripts to scientific Journals for peer review and publication sometimes at a fee....

03 August 2024 7,304 2 View

Why can't academics earn the money they deserve?

Only Journals make money from the articles we have worked on for years. Academics do not earn money from their refereeing. Then shouldn't the solution be a system in which academics can earn...

01 August 2024 6,469 6 View

Is it true that science is leaving the era of mathematics and entering the era of matrix mechanics?

We assume this to be true. Science leaves the era of mathematics and enters the era of matrix mechanics and the turning point is the discovery of numerical statistical theory called Cairo...

31 July 2024 3,900 2 View

Posthoc test lettering in JAMOVI?

Does anyone know of a module for the JAMOVI software that is capable of generating mean separations using the classic letters based on post hoc results (e.g., Tukey test)? If, as I believe, such...

31 July 2024 3,333 4 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,714 4 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,227 2 View

Varun Shah

M. H. Ashourzadeh Any vector graphic software will do the job. Will recommend Inkscape, it is open-source: https://inkscape.org/

Xuhua Wang

Sketchbook or AutoCad education version is free. Very good to draw such figure you referred. Please see the link

https://www.autodesk.com/products/sketchbook/free-download

Aman Arora

Use solidworks ( https://www.solidworks.com/ )