I have to prepare MRS broth and add 0.4% phenol to that media . How can I sterilize this media containing phenol?
Did you try UV sterilisation or radiation sterilization (i.e. gamma rays or electron beams). Radiation could be aggressive in aqueous medium, but performing irradiation on frozen state could help.
SIncerely,
Nicolas
I have design a 6GHz antenna for wifi.The feed line width is 2mm and there are 2 parasitic elements beside this feed line with 1 mm gap.Is there any problem at the time of febrication?
04 February 2021 9,241 3 View
I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...
01 February 2021 8,506 5 View
Seeking recent experiences in the development and deployment of low-cost soil moisture sensors (ideally under $50/sensor) connected to arduino-based dataloggers. What is the longetivity of the...
19 January 2021 6,256 2 View
I would like to develop a method for analysis of many organic acids in the same time. how to separate the chromatographic peaks of each one?
20 December 2020 8,399 3 View
I have a data set of 771 sample size. But some of the variables (laboratory findings like ALT, AST, creatinie level) have more than 50% missing values. Should I drop those? But I think those...
13 December 2020 4,847 3 View
We are finding a hard time to strip of residual HSQ ( Fox 16) after using it as a mask in etching? We are coating 600 nm thick HSQ and writing with 3000 microC/cm^2 dose at 1 nA current. We are...
08 December 2020 5,452 2 View
I am working with oral cancer cell line SCC090 (ATCC). As per ATCC data sheet it is originated from metastatic tongue. It's primary site is not mentioned. Due to the origination from metastatic...
08 December 2020 5,674 3 View
My sample size is more than 750 but sk test is showing non-normal distribution. The variables have several outliers but I shouldn't remove those. In that case what should I do? t-test or other...
06 December 2020 1,285 19 View
I am working with oral cancer cell lines and trying to find the expressional changes of HIF1alpha under different experimental treatment. I am getting intense band of HIF1alpha in the western blot...
29 November 2020 5,707 3 View
I am working with h-BN and need to find out the strain due to in-plane lattice constant. The famous Williamson-Hall method may not be applicable here as it analyzes XRD for calculation of strain...
19 October 2020 7,386 4 View
We want to use phenol pH graphic to measure the pH of mediums before and after inhibitor application to cells. We have phenol absorbence values at 460, 560 and 720 nm wavelength. When we measure...
20 February 2021 7,700 3 View
Hello, I am planning to do a transformation, and on the protocol it says "Scrape a 50 ml volume of yeast from the YPAD plate using a sterile inoculating loop or sterile toothpick". But I can...
14 February 2021 6,247 3 View
I use para nitrophenyl palmitate substrate with tris buffer ph 8... i read many temperature for Yellow color of para nitro phenol production.. 37 and 50 and 40 at water bath ... I confused as i...
04 February 2021 9,100 5 View
I am trying to run a cell viability assay with LN229, but these cells are cultured in DMEM which contain phenol red. Is the MTS assay sensitive to the additional of phenol red in the media? If so,...
03 February 2021 9,478 2 View
Dear Respectable Scientists, I have been trying to extract DNA from above mentioned sources using different CTAB/SDS Buffer Compositions and purifying agents but I am not able to extract DNA from...
12 January 2021 5,899 8 View
07 January 2021 6,527 3 View
I want to incorporate CNT in the alginate solution
23 December 2020 9,521 3 View
In microbiology to do plating, is there any need to sterile the DI water also?
22 December 2020 3,288 1 View
As different polymers with different characteristics are exist,I want to know What polymers can be used for packaging an orthobiologic product(bone allograft),which can have enough resistent to...
22 December 2020 8,196 5 View
Hi, I want to start my cell culture to run a MTT assay , how can I sterilize my polymer?
15 December 2020 1,813 1 View