How to do optimization in HEC HMS with snowmelt?

28 January 2018 1 5K Report

I have optimized my run when i dont use snowmelt but when i add snowmelt HMS does not optimize. Any solution_

I think in these conditions you should use other optimization methods. because, the Nedler-Mead method which is used is HEC-HMS model is not so good when the number of optimized parameters increase. Based on my experiences, I suggest you to use GLUE method. This model is based on several runs for different input combination...By searching on the internet you can find a lot of references for this method..

I hope that works..

the best

Azizian

Badges
Science topic

More Berkan erşahin's questions See All

How to calculate thermal conductivity values of heat transfer fluids based on therminol?

Where can I find the physical property formulas of terminols as in the picture I shared. Therminol 66, Therminol 62, Therminol VP-3, Therminol....(for all therminol heat transfer fluids)

27 April 2023 9,517 3 View

Thermal conductivity values of nanofluids with terminol base fluids?

Can you help with the thermal conductivity values of nanofluids with terminol base fluids?

11 April 2023 3,004 3 View

What are the differences between 20 kHz and 100 kHz initial frequency in EIS?

I want to measure the impedance of a microbial electrolysis cell. In the literature, they usually set the initial frequency to 100 kHz however, the potentiostat we have is limited to 20 kHz. What...

17 November 2022 1,748 2 View

Item parceling before or after exploratory factor analysis?

Hello, Recently, I've been reading and trying to learn more about item parceling procedure and SEM related concepts. My question is some studies utilize EFA before item parceling whereas the...

08 March 2019 7,913 1 View

What would happen if we used 45C instead of 65C as annealing temperature of colony pcr?

What if we used 45C instead of 65C as annealing temperature of colony pcr? Is there no band or band on more than we expected (I mean at 3kb instead of 1kb)?

26 August 2014 354 3 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

People weight in Oaxaca Blinder Decomposition on R?

Hello guys! Do you have experience running a Oaxaca-Blinder decomposition on R applying person weights. How do you suggest doing it? I have a variable PERWT which gives more information on how...

04 August 2024 6,033 0 View

How to perform EEG source analysis on each trial of data separately?

Hello Everyone I have a question about structure for connectivity analysis on sources. My goal: preprocess and cut data into trials create headmodels, using template MRI file perform source...

30 July 2024 2,744 1 View

How to add Cr parameter in autodock?

When I run autogrid4 it says: autogrid4: ERROR: Unknown receptor type: "Cr" -- Add parameters for it to the parameter library first! Look forward to your reply.Thank you so much!

29 July 2024 488 0 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How to use Desmond in HPC ?

Our department has recently acquired an HPC (High-Performance Computing) system, and I'm thrilled to take my molecular dynamics calculations to the next level using Desmond. I used to run my...

28 July 2024 6,553 1 View

How do I run a dead well test for a QuantStudio 5 qPCR machine?

I am preparing to run a lot of samples on a 384 well plate and I wanted to test if any well in my PCR machine is dead so as not to lose any data. I would really appreciate help with how I can do...

24 July 2024 8,172 1 View

VECM Model: Positive/insignificant CointEq1 ?

Hello everyone, I am conducting

22 July 2024 8,085 11 View

Merge Intensity Data from 2 runs?

Hi, We have collected several images for two independent runs of an experiment using two different confocal microscopes and settings. Thus, the intensity values collected through ImageJ were...

22 July 2024 8,722 0 View

What is the solvent system required to run tlc for calixarenes?

If you don't understand my question let me know

21 July 2024 563 1 View