Hi all
I have an equation of the form CxHyOz---->(decomposition) aCO + bCO2 + cCH4 +d H2
how can i get the values of a, b, c and d from elemental and proximate analysis of biomass?
x,y,z are unknowns
Thanks
To get the structure you need more data like C and H NMR, FTIR.
REGARDS
G
unfortunately, I only have this little bit of information from 2 papers
Article Analysis of Syngas Quality from Portuguese Biomasses: An Exp...
Article Improved numerical approaches to predict hydrodynamics in a ...
Make your calculations based on 1 mole where you can get then in terms of X and y for example for 1 mole of reactants y= 4c+2d
I got the solution from a paper.
Article Composition of Volatile Gases and Thermochemical Properties ...
You can use BS EN 15104:2011 Standard by CHN instrument.
Also, refer to scientific articles about biomass analysis.
Best Regards
What is the difference between MFIX and Fluent Eulerian multiphase modelling, particularly for fluidized beds. since MFIX is able to predict correct pressure drop below min fluidization velocity,...
01 February 2019 6,611 0 View
Hi In eulerian multiphase model, it is assumed that mass and momentum are transferred on a cell-basis. So, if cell size is smaller than particle size, it means that the math is incorrect. But...
10 November 2018 4,517 2 View
Hi I need to write udf for solid solid interaction using modified syamlal obrein symmetric drag model in ansys fluent. In the model, there is a term of radial distribution coefficient go,ls. I...
09 October 2018 616 2 View
Dear All, I am facing convergence problem in multiphase (eulerian-eulerian) problem Problem Description three phases: air, and two granular phases air enters from the bottom one slid phase is...
07 August 2018 6,608 15 View
Hi everyone I am going to simulate a biomass gasification problem. can I use COAL CALCULATOR for determination of volatile composition for BIOMASS gasification/pyrolysis from ultimate and...
05 June 2018 8,789 4 View
Hi all How to define biomass as granular phase in eulerian-eulerian multiphase model in ansys fluent? given that there is no biomass material type available in fluent database Thanks
05 June 2018 10,016 7 View
Hi all, I have some confusions regarding ultimate (elemental) and proximate analysis 1) Should the sum of all percentages be always 100 (for both analyses)? (Figure 1 attached, doesn't make...
04 May 2018 8,376 4 View
My case is a transient multi-phase simulation. I saved case and data every 100 time-steps (lets say there are 100,000 time steps). Now I want to write solution data for a variable (lets say...
31 December 2017 8,813 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View