How to design unity gain buffer for Giga Hertz frequencies with output impedance equal to 50 ohm ?

K Vasudev Reddy @K_Vasudev_Reddy

06 June 2016 0 2K Report

I am trying to measure S-parameters of LNA, so to match the output impedance with port a buffer is required .

Badges
Science method

More K Vasudev Reddy's questions See All

Can anybody tell me how to measure S-parameters of a differential LNA?

If it is with the help of Balun, What type of balun should I use Ideal/pract?

11 December 2015 686 3 View

Can anybody tell me how to set the common mode in single to differential output amplifier?

differential amplifier: Can anybody tell me how to set the common mode voltage in single to differential output amplifier?

10 November 2015 7,894 9 View

Which type of receiver architecture is preferable for low power RF Receiver front end?

I am planning to Implement receiver front end for low power RF applications,In this regard I have doubts like which type of architecture is preferred usually?i.e Super heterodyne/ Heterodyne/...

05 June 2015 9,851 5 View

AMAXA Lonza nucleofection lower volume of buffer?

Does anyone tried to do nucleofection with AMAXA by Lonza with lower than recommended amount of buffer in the cuvettes (100 ul)?

07 August 2024 4,616 0 View

Why I can't see any band in SDS-PAGE?

Currently, when I run SDS-PAGE, I don't see any bands at all, even though I used the same material just a day ago and it worked fine.... In our lab, we dilute the 10X running buffer to 1X and...

06 August 2024 5,373 2 View

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

What is the best blank for nanodrop if I want to read a recombinant protein concentration?

Is it the "elution buffer" or the "dialysis buffer"? Note: I'll be using NanoDrop OneC

01 August 2024 967 3 View

How to calculate conductivity using Electrochemical Impedance Spectroscopy's Nyquist plot?

Hello everyone, I am new to this characterization but watching videos on youtube I have already plotted a Nyquist plot (Z' and -Z'') and already fitted models on my material using Zsim. But now I...

29 July 2024 1,376 0 View

EDTA buffer solution?

Hello everyone! How can i prepare EDTA buffer solution (pH 8.2) to determine GSH levels? Thank you in advance.

29 July 2024 4,374 1 View

Whether i can preserve leaves samples in 2.5% glutaraldehyde in 0.05 M phosphate buffer, pH 7 for coming several weeks for further LM study ?

I want to preserve the sample leaves for the LM study of the stomata and conidia analysis. Whether 2.5% glutaraldehyde in 0.05 M phosphate buffer with pH 7 can be applied for preservation.

29 July 2024 8,560 0 View

Why semicircle of nyquist plot is not complete?

While I am doing HER, I noticed that nyquist plots of Electrochemical Impedance Spectroscopy (EIS) is not complete. Will it affect for the Linear Sweep Voltametry (LSV) data? However, I can found...

26 July 2024 7,542 4 View

What binder would be the best choice to modify glassy carbon electrode with a 2D Material like Graphene or MXene?

I am trying to drop cast 2D Materials on Glassy Carbon Electrode for Cyclic voltametry and EIS purpose. What would be best binders to use?

23 July 2024 5,776 2 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View