How to deposit thin film of PEDOT:PSS on ITO coated PET by spin coat. 483095 ALDRICH 1.3 wt % dispersion in H2O, conductive grade. Should I dilute it?

More Mirwaiz Rahaman's questions See All

Anyone having expertise on MedeA with VASP for electronic structure calculations of materials. Please respond..?

First principle simulation of Semiconducting nanomaterials with VASP.

01 February 2018 3,920 1 View

How the metal droplet forms in Vapor-Liquid -Solid growth. Is it the substrate which makes alloy with metal or target material?

VLS growth of 1D nanostructure.

04 May 2017 7,545 3 View

Adherance of Polyaniline coating over stainless steel?

Is the electropolymerisation of polyaniline coating over stainless steel (SS) via Cyclic voltammetry technique is really adherant? Else how to improve the adhesion of the coating, whether any...

01 March 2021 8,220 2 View

Is there a method of determining feed digestibility without the need to re-pellet the feed?

I am aiming to determine the ADC values of a commercial fish feed, but I do not have a steam pelleter or extruder available to me. Ideally, the pellets could be coated with some inert marker....

28 February 2021 7,967 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to immerse bricks in wax ( for coating ) ?

Do we immerse the bricks horizontally or vertically ? #bricks#waterproofingsurface#civil#engeenering#chemicalengineering#wax#parafinwax

28 February 2021 6,685 2 View

For gelatin coating for culturing HUVEC.Should the gelatin be made in sterile water or PBS? Do I need to autoclave the gelatin soln after making it ?

I want to use 0.1% gelatin. Should that be made in PBS or sterile water? Should I autoclave the gelatin soln after making it in water/PBS?

28 February 2021 274 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What is the best surface to culture cells isolated from a skin biopsy?

Hello, recently I am having some difficulties with maintaining the cell culture of primary cells isolated from a skin biopsy (normal and malignant). The coating of culture plates with Matrigel (a...

26 February 2021 6,151 2 View

Unknown debris sheets observed in cell culture flasks?

Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...

25 February 2021 3,443 4 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Selva Kumar

Normally your solution is very dilute when you are doing spin coating, the solution may spread in coating unit, so dont dilute it, instead of that make it concentration more and spread it high viscous solution.

In this case you have chance to get film. Good luck.

S. S. Kalagi

No need to dilute the solution further.you can get good film by adjusting the spin speed.Keep it less initially till the solution spreads on the substrate say 200 rpm,then increase the speed to 2000 to get uniform thin film.you can try with different speed combinations for best results.

Mirwaiz Rahaman

thank you Selva Kumar and S.S.Kalagi.