How to define the Al foam infiltrated with 90% PCM in fluent?

Karthikkumar Ramiyakrishnan @Karthikkumar-Ramiyakrishnan

13 August 2018 0 9K Report

Hello Guys,

I would like to know how can i define Aluminium foam that is infiltrated with 90% PCM for the solidification/melting process in fluent? On an early reply will be highly appreciated.

Badges
Science topic

More Karthikkumar Ramiyakrishnan's questions See All

Simulation of Phase change material in Ansys Fluent?

Guys, can someone share me the fluent file for the simulation of melting/solidification of Phase change material?

01 July 2018 5,066 4 View

Simulation of Paraffin Wax in Ansys Fluent?

Guys, I am working on simulation of Phase change material in Ansys Fluent. I have used Pressure based solver, transient calculation, Viscous laminar flow and incompressible ideal gas law for...

01 July 2018 7,791 4 View

Simulation for thermal electrical analysis in ANSYS AIM 18.1?

Hello Guys, I wanted to perform simulation for phase change material using Ansys AIM 18.1. I am planning to implement Joule heating concept (thermal electrical analysis) as a heat source to...

15 May 2018 4,480 1 View

3D modeling of Metal foam?

Hello Guys, Can someone share with me about the 3D modeling of closed cell foam? Kind regards, Karthikkumar

15 May 2018 515 4 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

How can the rubber fibres produced by the electrospinning device be removed from the fibre collect(aluminium foil) ?

How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...

26 July 2024 8,281 0 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How does surface energy affects the solidification of polymer?

Dear All, I would like to ask about the relation between the surface energy and solidification of polymer. If we apply a chemical treatment such as NaOh solution or silane treatment on the...

17 July 2024 190 3 View

How to prepare alcohol foam with high alcohol content?

Hi everybody, I wonder is there a way to prepare foam from iso-propanol/water mixture? The content of this alcohol should be 70 – 80 w.%. I plan to use silicone-based surfactants, I have several...

15 July 2024 3,539 0 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to remove aluminium oxide from powder ?

I synthesise intermetallic compounds through nickel and aluminium powders. But the pure powder after synthesis is difficult to obtain. Especially the presence of aluminium oxide very seriously...

01 July 2024 4,030 3 View

Staining of foam cells derived from PBMC differentiated to macrophages. Does anyone have experience with this type of assay?

Hi everyone, I am trying to induce foam cells in macrophage differentiated from PBMC. Which type of staining do you prefer to use? Nile Red or Oil RED O ? What concentration and timing of ox-LDL...

01 July 2024 8,286 0 View