How to define a sample in ZEMAX Optic Studio 13??

24 January 2022 1 6K Report

I am working on the simulation of the Ti: Sapphire cavity in ZEMAX (non-sequential mode) I want to introduce the sample in the cavity design but I don't know how to define a crystal or sample in ZEMAX.

Badges
Science topic

More Muddasir Naeem's questions See All

How to improve the adhesion of epoxy coating on steel substrate? Which factor affects?

I am facing a problem regarding a de-adhesion problem with the coating. A brief description of my methodology is given below. I am using mild or Low Carbon steel as a substrate and I polish the...

14 February 2021 2,167 4 View

Why mutual inductor takes high current at no load condition?

I simulate an inductive wireless power transfer system in matlab. I set the primary and secondary mutual inductor resistance is 0.3ohm. So when i run the circuit it took high current at no load...

29 December 2020 9,536 3 View

Can I see nanoparticles using optical microscope with stage micrometer?

I am working on Solid Lipid Nanoparticles I am doing MPhil research I am preparing a formulation My topic is Preparation AND Evaluation of Indomethacin Loaded Solid Lipid Nanoparticles for...

27 October 2020 9,496 4 View

To what extant the GIS Thematic Mapping Approach is significant in the analysis?

Today, GIS is being considered the most significant and highly recommended technique in analyzing data and its also argued that in Pakistan too few people use this approach in the analysis of...

12 March 2020 5,317 5 View

How to calculate the elemental concentration in infusion and decoction?

If infusion was prepared by adding 2g of dry tea powder to 200mL boiling water (ratio of 1g per 100mL) for 10 minutes. It gives a factor of 100 for multiplication with instrumental concentration...

16 January 2020 1,844 3 View

What's the best way to detect the extracted lipids in order to confirm that your lipid extraction protocol is correct?

I am extracting Lipids from RBC Membranes using the Cholorform/Methanol (2:1) method. After phase separation and consequent evaporation of the organic phase, what would be the best way to confirm...

02 December 2019 8,050 2 View

Anybody can suggest me any solution why matlab stop working?

I installed different versions of MATLAB. After successful installation, when open the command or editor window, it is freezed/hanged. Before that it was working properly and suddenly start facing...

30 July 2019 4,244 3 View

The study of Marxist literary work in Pakistan.I want to know how Mohsin Hamid deals with economic disparities in his novels?

The focus of my attention is on Mohsin Hamid's novel How to get filthy rich in rising Asia?

21 December 2018 4,371 2 View

Hello dears; can anybody help in arranging data in excel multivariate analyses using repeated measures in SPSS?

08 April 2018 8,188 5 View

Can I perform histopathology on cell lines?

I have transfected cell line with an inhibitor of a particular gene. that gene promotes tumor growth. Now I want to check whether the inhibitor has caused change in the tumor growth. So can I do...

25 February 2018 142 6 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What is the difference between Graphene Oxide and Expanded Graphite?

What are the main differences between Graphene Oxide and Expanded graphite, in terms of surface functionalities, conductivity, d-spacing and other features? Is the term expanded graphite...

06 February 2021 9,810 4 View

PEG coated Fe3O4 nanoparticles in aqueous NH3?

Hello, I synthesized PEG coated Fe3O4 nanoparticles by coprecipitation methods and I would like to ask whether they can be dispersed in aqueous NH3 since they have a PEG coating and theoretically...

06 February 2021 5,217 4 View

How to apply graphene oxide on an gold electrode?

Dear Fellows, now it is the time to push graphene applications further in terms of easy and low cost production surroundings. Thus I recently dived in the materia and I am facing tons of papers,...

02 February 2021 6,284 2 View

Can I use aluminum or copper based substrate for DNA origami imaging using SEM?

As suggested in the title I want to image my DNA nanoflowers/origami using SEM. These nanoparticles are an organic-inorganic particle made out of highly packed DNA and also contain magnesium...

28 January 2021 3,343 3 View