I am using Lithium 2RC Matlab model. Does anyone know how to compare this model output to experimental data and find out the Root mean square error values ?
Hi, At 1C-rate, I am doing OCV test on A123 li-ion cyclindrical cells to measure capacity & internal resistance. At the end of discharge cycle how long is the pause time after which I can...
07 August 2018 8,601 2 View
I am performing EIS (BRS Messtechnik, galvanostatic) on cyclindrical A123 26650 LFP full cell. After setting SOC it is required to wait for some hours before carrying out EIS. I know it is to...
05 June 2018 9,208 0 View
Hi, I have 9 26650 LFP cells connected in series and impedance is measured one after the other using BRS EIS device. Currently I have soldered the batteries, but the EIS spectra is not a good...
04 May 2018 5,435 0 View
I have set of Electrochemical Impedance spectroscopy data of Lithium ion full cell (26650). Then I do Kramers-Kronig fitting using Lin tool of KIT. But this tool allows one cell after another...
03 April 2018 7,728 0 View
Hi, file='Data.xlsx' M=xlsread(file) Now I want to create a text file of the same name as in the excel name fileID=fopen() Can anyone tell what command comes here ? like sprintf or something...
03 April 2018 6,353 6 View
Hi, I have about 100 excel.xlsx file and wanted it to read with some Scilab xls or csv function. I could read this excel xlsx format. Also I don't want to use the import data format as I have...
03 April 2018 1,734 0 View
Hi, Similar to Matlab xlswrite(filename,A), what is the function name in Scilab to write on a new excel file ? I tried searching, but couldn't find out. There was only write_csv...
03 April 2018 5,581 2 View
Hello, I have 100*10 matrix. I don't need the first 13 rows (they are strings). I need all data from 14th row. One columns (6) contains string which I don't need. Can anyone tell me how to read it...
03 April 2018 8,759 0 View
Hi, I have matrix 'x' (see pic) with 5 values. Out of those one value deviates from the rest. So when I take the mean, standard deviation and plot with errorbar in Matlab, the deviation seems to...
02 March 2018 468 3 View
I am using equivalent circuits to fit 26650 LFP's current pulse measurements. We know that as temperature increases, the resistance decreases because of the ion's mobility. But at the same time,...
02 March 2018 250 9 View
I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...
13 August 2024 9,795 0 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
This larva was captured using a plankton net in the Persian Gulf during the summer. I believe it may be a Facetotecta nauplius.
08 August 2024 3,746 4 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View