How to coat zinc oxide over a glass substrate using electroless method?

More Gautam Subburaj's questions See All

How to calculate the fraction metabolized of a drug by an enzyme using clearance(ml/min) values of the metabolite formed?

I am trying to find the fraction metabolized of a drug by CYP and UGT enzymes. I am unable to get the values of fraction metabolized (Fm) directly from the literature. Can we calculate the Fm of a...

21 February 2021 5,379 2 View

How to compile UDF for parallel processing ?

I am trying to use a UDF for velocity input in the room from a fan. I have created a UDF but when I am trying to load the UDF it shows an error stating that it is not compiled for parallel...

03 February 2021 2,187 3 View

What will be the life of siRNA (liquid form) at -20 degree, if kept unopened?

Hi all, I just want to know that, if we keep the siRNA in a -20 degree freezer (as mentioned in the product detail), what will be the average life of the siRNA? Can we store for more than one...

10 January 2021 6,346 6 View

Is there any method to convert color on nitrocellulose into digits (numbers)?

This is to design a protocol in which color obtained on nitrocellulose membrane can be converted or processed through any method to digits (numbers) to compare with different state of particular...

06 January 2021 9,309 1 View

Vertical distributions of SOC & N is found decreasing with increased value of bulk density, shown in literature, is it uniform for the forest soils?

Almost all the literature shows that the vertical distributions of soil organic carbon (SOC) & available nitrogen (N) is found decreasing with increased value of bulk density with respect to...

21 December 2020 670 10 View

Can difference-in-difference approach be used between two treatment groups?

I want to know if difference-in-difference approach can be used for two treatment groups. Can I use it it between them or should I first identify a control group and then compute the diff-in-diff...

20 December 2020 2,825 1 View

Is there any chemical environment or parameters to define or explain the sediment and soil profiles, are they separated by chemical parameters?

Sediment is relatively younger than the soil in the depositional environment as the sediments are consequence of the accretion of particles transported either by waters or by winds, whereas, soil...

12 December 2020 4,822 18 View

Bulk density obtained of the forest surface soils is 0.81 gm/cubic centimetres, is it normal?

Bulk density of a forest soil sample in a community forest created under social forestry scheme in the district of Nadia, West Bengal is obtained as 0.81 gm/ cubic centimetre, comparatively too...

30 November 2020 4,706 33 View

Is it possible to grow human breast cancer cell lines in immune competent mice?

Hello everyone, I am working in breast cancer and wanted to do in vivo studies in breast cancer mice models. Here we do not have the facility to maintain immune-deficient mice, and I have MCF-7,...

27 November 2020 1,638 3 View

What's the actual content of carbon in biomass, is there biomass carbon neutral or zero carbon?

The content of carbon in the biomass varies from 35% - 65% in one literature, in the another, it's 45-50%, though 50% is often taken as default value, and all they are surprisingly constant...

23 November 2020 1,736 7 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

Glass fiber content in a gypsum board ?

Any idea on how to get the volumic ratio of glass fiber in a gypsum board ? Thank you for your help !

01 March 2021 2,501 3 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

How to properly calculate the fluid solid heat transfer between polypropylene matrix and glass fiber in a porous medium?

I'm building a cfx model of thermoplastic pultrusion process on ansys and i have a doubt on how is the proper way to set this parameter in a porous medium

24 February 2021 1,915 1 View

How to properly calculate Interfacial area density in a porous domain?which are possible value for glass fiber?

I'm doing a cfx simulation of a multiphase flow in pultrusion and i set the Interfacial Area density in the heat exchange of a porous medium in this way IAD=Total fiber lateral surface of fiber...

23 February 2021 6,043 1 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

Aadithya Jeyaranjan

Chemical Bath Deposition, maybe ?

B.J. Lokhande

by using spray pyrolysis via non aquous route you can coat zink oxide.read more in my paper spray pyrolysed zno by spray pyrolysis

Prashant Sharma

In this paper we have grown ZnO nano wires on glass cover slips.

Hope this can help:

Article Efficient intracellular delivery of biomacromolecules employ...