How to choose a Combustion model based on Turbulence effect inside the combustion chamber.?

More T.Karthikeya Sharma's questions See All

What's the effect of magnetic field on rate of heat transfer through conduction...?

I have one doubt can't we enhance or suppress the rate of heat transfer through conduction by using magnetic field inline and reverse to the flow of heat? as the both conduction and magnetic field...

01 February 2016 4,737 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 718 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Abhilash Kumar Tilak

Homogeneous charge compression ignition (HCCI) is a combustion process that combines the ignition process of a compression ignition (CI) engine with the premixed nature of the spark ignition (SI) engine. The HCCI engine platform is nearly the same as the traditional CI engine.

http://ac.els-cdn.com/S2215098615301762/1-s2.0-S2215098615301762-main.pdf?_tid=dea391fc-d078-11e5-bbd4-00000aab0f27&acdnat=1455165505_748dfd06b95878dd1a30c90ba12f7d5f

http://ac.els-cdn.com/S0378382015302472/1-s2.0-S0378382015302472-main.pdf?_tid=c84c7fe0-d078-11e5-9439-00000aacb35f&acdnat=1455165468_88c67f708d3c9ef3565f3813c54dc4b3

Amir Javad Ahmadian Hosseini

Dear T.Karthikeya Sharma

One of the best combustion models that based on turbulence effects is Magunessen Eddy Dissipation model, this model is simple because of eliminate number of species and has a powerful validation advantage with experimental data.

Good Luck