How to check pressure from autoclaves?

sn Tadka @Sn_Tadka

06 June 2018 1 5K Report

I have hydrothermal set-up from that i want know how much pressure is maintaining inside?

Osama Rahil

Dear Sir

I think the links below will benefit you in your search

https://sterilizers.com/autoclave-time-temperature-pressure-chart.html

https://consteril.com/how-to-calibrate-your-autoclave/

https://consteril.com/steam-autoclave-answers-to-3-common-maintenance-questions/

http://www.ucl.ac.uk/medicalschool/msa/safety/docs/LaboratoryAutoclaves.pdf

Best Regards

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More sn Tadka's questions See All

What is the best and easiest way to do for grinding of nano silver powder?

I have triple roll mill which having dia of 10cm each. with cooling system. here i should do for 50gms of silver gel unform mix. Can you give the suggestions for how to utilize this mill for...

01 February 2018 7,744 2 View

What is the proper and standard procedure for to take correct reconstruction of the micro size ceramic material from X-Ray CT Microscope?

I have 25mm thickness ceramic based micron size particle material. Apart from I want to do correct reconstruction of the material from X-Ray Computerized Tomography Microscope(XT-400). which one...

10 November 2017 8,674 1 View

What is the best way of techniq to get continueous ultra thinfilm(<100microns thickness) from carbon aerogel based powder form material?

Material synthesized by poly condensation method.Material having mesoporous structure,specific surface area arund 500m2/g.

01 January 1970 3,757 0 View

How to caluculate Internal and External Surface Area of the micro porous materials?

If we have carbon mesoporous material for caluculating the total specific surface area(external&internal) but how?what method we should follow?and If any possibility is there to maintain...

01 January 1970 9,536 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Question about water vapor uptake of metal-organic frameworks?

I'm working on the atmospheric water harvesting, and i synthesized MOF by adding some materials into precursor and changing the conditions. (i followed Hydrothermal method) Actually, if MOF is...

24 July 2024 1,515 0 View

I want to buy Hydrothermal Synthesis Autoclave from any European company. Can anyone suggest any company inside Europe?

Thanks

22 July 2024 1,143 3 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Is it necessary to autoclave every vessel used in DNA isolation?

DNA isolation requires many freshly made buffers. So is it necessary to autoclave each vessel used, before preparing buffers in them?

10 July 2024 7,526 3 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View