How I can balance three level Voltage source converter in simulink?

I am designing an Electric vehicle fast charging station in Simulink. I am using a three level voltage source converter. Can anyone suggest me how to balance this converter by using suitable...

08 September 2019 2,214 3 View

Can anyone suggest me any software to calculate parameters for Three Phase AC Source like R & L and parameters for connected distribution transformer?

I am designing a simulink model which is having three phase source (13.8 kV). I would like to know how can I calculate the values of source resistance and inductance and further parameters of...

10 November 2018 7,730 0 View

Can anyone suggest me method to calculate value of Resistance & Capacitance of Passive filters?

I am designing a Simulink model of a Battery Charging System. I need to design a passive filter and need to calculate the value of resistance and capacitance.

09 October 2018 3,718 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Are there lab markers/pens resistant to Roti-Histol?

Hi, I'm looking for a pen/marker to write on the smooth, transparent (non-frosted) part of microscopy slides which does not get washed away by alcohols and most importantly Roti-Histol. I want to...

24 February 2021 9,902 5 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

I have a problem with kanamycin - why the kanamycin doesn't affect?

Hi everyone, I need to expression of GFP with pET28 plasmid in E. coli BL21(DE3) plysE. Transformed cells have kanamycin and chloramphenicol resistance. Normally, only transformed cells should...

22 February 2021 4,032 4 View

How can I get "Matlab/Simulink model for Droop/Reverse Droop controllers"?

Dear Professors, Colleagues and Friends I need to develop a simple Matlab/Simulink model of reverse droop controller for a simple LV MG. How can I get a simple one to use it as a sample? A basic...

22 February 2021 8,647 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View