Can anyone suggest me method to calculate value of Resistance & Capacitance of Passive filters?

More Gagandeep Sharma's questions See All

How I can balance three level Voltage source converter in simulink?

I am designing an Electric vehicle fast charging station in Simulink. I am using a three level voltage source converter. Can anyone suggest me how to balance this converter by using suitable...

08 September 2019 2,214 3 View

Can anyone suggest me any software to calculate parameters for Three Phase AC Source like R & L and parameters for connected distribution transformer?

I am designing a simulink model which is having three phase source (13.8 kV). I would like to know how can I calculate the values of source resistance and inductance and further parameters of...

10 November 2018 7,730 0 View

How to calculate the Inductance of Underground cable (Electrical Distribution circuit) for a particular distance ?

I need value of inductance for Simulink model of the distribution network. I would also like to know how to calculate value of Resistance and capacitance for the passive filter.

08 September 2018 3,137 4 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

How to calculate Total Flavonoid?

I analyzed flavonoid total spectrophotometry, the procedure as below: 2 ml supernatan added 5 ml dd.H2O, then added 0,15 ml NaNO2 5%, 5 minutes later added 0,15 ml AlCl3 10%, After 6 minutes,...

01 March 2021 6,722 1 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

RNA-seq DEGs downstream analysis and reporting in literature?

I used EdgeR to get the list of DEGs (differentially expressed genes) from my liver RNA-seq experiment. I have done the gene overrepresentation and GSEA based pathway analysis. I am currently...

23 February 2021 8,969 1 View

What are the ranges of four diffterent poles of butterworth filter for ECG signal?

Hi, Can anyone please tell me what are the ranges of four different pole orders such as first order, second order, third order and fourth order respectively of butterworth filter for ECG...

23 February 2021 2,554 3 View