How to do the calculation for super oxide dimutase assay and how to calculate the R squared value in regression equation for catalase assay?

i have the enzymatic antioxidant assay by following the method of Misra and Fridovich, 1972 for super oxide dimutase and Luck, 1974 for catalase assay can any help me how to the calculation for...

11 February 2021 2,241 3 View

The peptide synthesized with CTC resin have mass more (+68 Da) than the desired mass of the synthesized peptide. What could be the reason?

I am synthesizing 7 amino acid long peptide sequence with CTC resin, 50oC coupling for 10 min. On cleavage (TFA/TIPS/Water 95:2.5:2.5) I got peptide with good yield. However, It has 68 Da more...

30 January 2021 8,483 3 View

For VANET related issue /problems like congestion , MATLAB or NS2/NS3?? Which will be more suitable for implementation??

I have gone though few papers related to this problem. Researchers used NS2.35/2.38. and MATLAB. Also. My particular question is regarding congestion control . Which will be more suitable to use ?

22 December 2020 8,197 10 View

2 subsequent saccade and fixation duration after filtering 'unclassified' and 'eye not found' data in Eye tracking study?

My study is to use only fixation and saccade data. But after removing :unclassified' and 'eye not found' data. I come to know there is 2 back to back fixation duration or saccade what I need to...

28 September 2020 9,919 3 View

How informal learning can impact the learning culture of the organization?

Need to know specific parameters which impact the learning culture variables.

23 September 2020 233 4 View

How can i simulate dual-X second generation current conveyor using CMOS?

24 August 2020 8,067 4 View

In quantitative study, for calculating sample size, can the precision be taken 0.08?

In health related studies, can the level of precision be taken as 0.07 or 0.08 while calculating sample size?

19 July 2020 3,230 3 View

How to overcome the mismatch due to connector(50 ohm) and wire that is dipole(75 ohm)?

while designing the dipole antenna how to overcome the mismatch

31 January 2019 9,071 2 View

Is 100% connectivity is necessary for wireless sensor network ?

Here, we define average connectivity ratio as the ratio of number of connected sensor nodes to the number of sensor nodes deployed in the wireless sensor network. A 1- connectivity problem is...

04 May 2018 3,023 8 View

How can i apply to contribute toward the vernacular architecture of karnataka in west coast India ?

i am presently writing paper on climate responsiveness of the architecture of this region. i have many case studies yet to be published on this topic. roughly 10- 15 types documented and another...

12 September 2017 9,320 3 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View