How to calculate pressure autoclave knowing only temperature and volume of filling ?

30 November 2023 0 4K Report

How to calculate pressure in 100 mL capacity autoclave in the case of reaction taking place at 120 °C in 50 mL water filling ? (Given ramp rate is 3 °C min/1)

Badges
Science topic

More Novuhulu Rhakho's questions See All

Can self-assembly of a magnetic nanoparticles happen without any solvent evaporation method or external magnetic influence?

I observed an assembly process of a ferromagnetic nanoparticles into a 3D cubic microstructure in aqueous media at 120°C. However the assembly process didn't involve any solvent evaporation or...

27 November 2023 7,415 2 View

Can self-assembly of magnetic nanoparticles occur without any external magnetic field or solvent evaporation method?

I observed an assembly process of a ferromagnetic nanoparticles into a 3D cubic microstructure in aqueous media at 120°C. However the assembly process didn't involve any solvent evaporation or...

01 January 1970 8,725 0 View

Can self-assembly of a magnetic nanoparticles happen without any solvent evaporation method or external magnetic influence?

01 January 1970 5,057 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

I want to buy Hydrothermal Synthesis Autoclave from any European company. Can anyone suggest any company inside Europe?

Thanks

22 July 2024 1,143 3 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Is it necessary to autoclave every vessel used in DNA isolation?

DNA isolation requires many freshly made buffers. So is it necessary to autoclave each vessel used, before preparing buffers in them?

10 July 2024 7,526 3 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View