How to calculate mass balance based on feedstock molecular weight to determine biogas composition and account for losses and carbon not recovered?

More Syed Asad Ali Zaidi's questions See All

How to deal with nanoparticles containing waste?

Dear all, I am curious about the distribution of nanoparticles in the anaerobic digestion system, especially, in the wastes. And also, how to deal with the wastes with these pollutants after the...

31 December 2018 7,180 11 View

What methods can be used to measure Carbohydrates and Proteins in micro-algae?

I have green micro-algae (Enteromorpha) powder and want to measure the carbohydrates and proteins before and after the anaerobic digestion of this micro-algae with anaerobic sludge. Please...

02 March 2018 3,517 10 View

What techniques or methods one can use to find different behavior of same microorganism with different substrates in Anaerobic digestion?

I used four different substrates and inoculated them with four different types of nano particles. I found that the same microorganisms behave differently in the presence of the same NPs, but with...

10 November 2017 8,729 4 View

Can anyone suggest a good book on Florescence In-situ hybridization and FQ-PCR used for microbial analysis?

Thanks and Regards,

10 November 2017 6,194 1 View

What are the ways to measure cellulose and hemicellulose?

Which one is the easiest way to measure them

03 April 2017 6,050 2 View

Is it always better to have more choices?

Dear colleagues, your opinions and comments are welcome.

01 January 1970 3,878 31 View

Biogas plant optimum economic size

What is the optimum size of a biogas plant at which the cost per cubic meter is minimum? Thanks

01 January 1970 5,551 3 View

Graphene Oxide Nanoparticles

Kindly anyone please share the method of preparing graphene oxide nanoparticles. Thanks

01 January 1970 4,527 12 View

No title

What are the challenges and outlooks?

01 January 1970 8,533 4 View

How do you write an effective introduction for a research paper?

01 January 1970 2,045 46 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to quantify carbon deposition on CuZnAl catalyst?

Dear All, I want to quantify carbon deposition on the surface of the CuZnAl catalyst. I have tried thermogravimetric analysis, but I've got weight gain as the active Cu- get oxidised. Does anyone...

01 March 2021 1,907 3 View

Why Trivalent chromium start precipitating above PH 5 ? Moreover discuss difference between adsorption of chromium and precipitation of chromium ?

I am a student of MS Environmental Engineering and started my research phase. I am working on metal removal ( chromium iii ) by using activated carbon prepared from the agricultural feedstock. So...

01 March 2021 5,475 2 View